Hello Everyone, We encountered an issue with Sophos firewall XG. The issue simply is when we try to open the Banking website to do transactions or online banking, we authenticate normally. However, when we try to access anything in the bank website…

I need help with setting up my MG 125 device for bandwidth management. Can it do the job well? Thanks

Hello, I'm new to Sophos, and am deploying my first firewall to a very basic client, and just want to check what I have configured is a reasonable balance between security and functionality? I am just looking for opinions and whether I have missed anything…

Hii Community, I configured a firewall rule for VPN to LAN connection and another for LAN to WAN connection, attaching a NAT rule with MASQ for internet access. Despite this, I could establish a VPN connection with the Sophos Connect client but couldn…

Hello, I have a situation where my ISP installed a router and gave me a subnet ( 10.1.1.0/24 ) with the gateway being the router(10.1.1.1). My understanding is that I need to configure an internal network (i.e 10.1.2.0/24) on the LAN side of the firewall…

Good morning, I currently have a server in an on-premise datacenter that responds to TCP port 12233. So there is a very normal DNAT on the XGS firewall of the public ip 80.80.80.80:12233 towards the private server ip 192.168.1.10:12233 This service is…

Hi, I am really confused about how to do this on XG. I can go to Traffic Shaping and create my policy and attach it to my rule or service - but then in Traffic Shaping Service there is a setting "Optimize for real-time (VoIP)" that is Enabled by default…

hello , i'll try a simple port forwarding when i setup this like below , it works when i change the source port to 7887 then it dont forward. why o why ?

I believe I have everything right but I cannot see traffic in the firewall logs and I cannot get remote access to ether media server. NAT Rule : Port 2 is WAN, Port 1 is LAN, Synology is a local IP Any Suggestions? I already called my ISP and they…

Update to LAG not working unless you specify interface speed Using XGS4500 on 20.0.0 GA-Build22 with XSAZTCHF4 "Sophos FleXi Port Modul 4 port 10GbE SFP+" LACP bonding was not working on PortsA1-A4 unless specifying 10G Interface Speed manually, disabling…

Our organization recently deployed a Sophos Firewall to manage our network security, but we're experiencing some performance issues such as slow internet speeds and intermittent connectivity problems. I want to ensure that the firewall is configured correctly…

Hi, Can anyone confirm whether Sophos supports /31 subnet config on WAN interfaces please? XG2100 running SFOS 20.0.0 GA-Build222 Thanks

Hello everyone! I have 2 SOPHOS firewalls in two different buildings, connected by Long Range Aerials (point to point). FIREWALL 1 is configured like this: LAN 192.168.122.X (Aerial 1 is part of this DHCP pool) WAN public IPs (static) then…

Hi everyone, I have configured a bridge on ports 1 and 5 I would like to know if it is possible to configure a traffic shaping on a specific port. for example, port 1 with 10MB, port 5 with 40MB, I have created the this rule but I'm not sure if it really…

Hello, we are facing some performance issues on our XG650 running SFOS 19.5 MR3 and during investigation I have found that one of the Processors has significantly more load than rest of the 40 ones. Sometimes it is loaded up to 100% for tens of minutes…

Hi! I am a proud owner of XGS 107 and pretty happy with it. I am running a homelab with a few vlans, really nothing special. But there is something, that is bothering me: I am also using Barracuda Firewalls where i work, and there i really like the…

I have recently switched to a new ISP who allows me a blistering 3GB connection of which I wish to take some advantage. To do this, I rebuilt a new firewall from scratch with a 1Gb onboard NIC, plus a 2x10Gb NIC. This gives me 3 ports, which are in order…

Hi, I have configured the Policy in the Sophos firewall for the AV devices with traffic shaping (QOS) We need to monitor the bandwidth utilization of the policy, and need to know how much bandwidth its utilized, Is there any way to do this ?

Hello, I am using XGS2300 Version 20 When users are on LAN, they cannot access servers on the same network while using their public IP, they can only access the server over the public IP when they move out of the network. How do I solve that

After installing Sophos XGS2300, our client stopped viewing his Dahua CCTV remotely on his smartphone, the NVR is online in the AP but CCTV footage is not I dstreaming. I did all the necessary port foward and ports are open RTSP: 554 TCP: 37777 HTTP…

Using xg 135 model. Updated to the latest firmware however, some sites provider.cignaenvoy.com are unreachable. I am able to get a reply when I ping the site.

Hi all, Today I have a new problem which dates back more than 3 months to configure the firewall with the Nokia FTTH modem in bridge mode. -Sophos XG86w -FTTH modem Nokia: G-1425G-B The Device is a router with built in GPON ONT - it is for broadband…

Hi all, We have a very busy site, with a 1Gb leased line connected to an XGS2100. I'm reading the Sophos literature on traffic shaping and wanted to check really how to get a simple approach fixed. Note, half our users are mac based, so we don't…

Hello Sophos, As an Internet provider, we have had extreme problems with geolocation in recent weeks. As we have now found out, this mainly affects services and applications that use a Sophos firewall. Our IP addresses are probably recognised here as…

Hello Team, We are using the Sophose XG firewall, I would like to raise the concern regarding WAN Ports are not working, can you please help on it