Hi, I am trying to get QAT support information on the current XG Home v21. The last document that mentioned QAT was version 18. Is QAT still supported? If so, what can be offloaded to it?

Hallo Zusammen, ich habe eine Sophos XG135W. Auf dieser läuft XG Home. Nach meinem gestrigen Neustart, starten nun nicht mehr die LAN Ports. Beim starten leuchten diese kurz auf, danach gehen Sie aus und haben auch keine Funktion mehr. Weiß…

So -- in the olden days we could take old retired SG appliances, wipe the drive (delete partitions with Gparted, etc.), and load SFOS Home on them -- we had engineers that would run them at home for training, and to test bleeding-edge releases, etc. Apparently…

Hello, I have Sophos SG 330 Rev. 2, completely new. I have used a USB installer to install the community/free edition of SFOS. The installer went ahead correctly, installing OS on the local SSD, and the appliance rebooted. After I saw that the appliance…

Dear community, I recently purchased a pre-owned XGS116w appliance and would like to run the home license on it. There are several forum posts how to start to get a home license onto a XGS hardware, but I could not find any which actually stated "I…

Hello everyone, I am about to install Sophos Firewall Home Edition v19.5 on the HP T730 ThinClient barebone x86 desktop installed with a 4-port FastLinQ QL41134HLRJ 10Gbe NIC. The NIC sports a Cavium DPDK high-speed packet processing engine. As handling…

Hi, Summer time and I need to monitor the Sophos Home firewall mounted on Protectli. In advances shell sensors command doesn’t work and I cannot find any way to monitor it through api or whatever mode. I need to monitor the temperature please could…

Hi, I purchased a used XG 115 Rev. 2 firewall and installed Sophos Home Edition so I can use it as a perimeter firewall at home. My internet connectivity is FTTH 1 Gbps/300 Mbps. If I connect directly to the ISP router by running a speed test I get 900…

Good morning, I've got a XG135 Rev3 that I'm planning on installing XG Home on. Is there speedstep support within the BIOS and is the fan supposed to be controlled by PWM depending on temps etc? It's been delivered with pfsense installed on the unit…

Hello all, 1.) I've heard some rumors that sophos firewall home edition will be end of life at some point in that not too distant future, is there any truth to this? 2.) Are there any fanless mini multi NIC pcs that have 2.5gbe that the sophos utm…

Olá, tenho um sophos xg86 no meu laboratório, gostaria de saber se é possível instalar a versão home nele, visto que a licença vai expirar em 1 mês.. é possível ? Como eu faço isso, visto que ele não tem conexão pra ligar monitor.

Quick question: Do you have to have Sophos Hardware to make VLAN work in the firewall software? I'm using a mini pc running Sophos Firewall V20 and it appears when I set up a VLAN, it doesn't work. Followed the directions on how to create a VLAN but…

Installed home firewall on XG 125w rev3. The software shows ports 5 and 6 as Port 1 (LAN) and Port 2 (WAN). It seems all of the ports are numbered wrong. Is there any way to configure the software to see the correct port numbers?

What are the differences between the XG 125 revs (rev 1,2,3)? Would the rev 1 processing power be sufficient for a home network?

I’m looking for some advice for Hardware for the Sophos Firewall Home Edition. I’m not sure if I should use a vm or bare-metal installation. When I was looking for some hardware, I found HPE ProLiant MicroServer Gen10 Plus v2 with an Intel Pentium…

Hi, I,m going to install Sophos XG home edition to a Protectli vp2420, I know the 4 core and 6GB ram limitation but with 300mb/s internet bandwidth it should be enough. It would be possible to install Sophos in Raid 1 if I provide Protectli with 2…

Hi everyone I installed my Sophos Home on a Mini-PC but it does not shows my NICs up. specs Intel Celeron J4125 8 GB RAM 256 GB SSD 4x 2.5 GBps LAN (i226-V) Any idea what can solve my problem? Thx

Hi, I'm not sure if I have just locked myself out of using XG home firewaill because of an unexpected BIOS compatibility issue. My ancient PC (Pentium III) mobo died. It was running XG 19.x. Researching for microPC's (ServeTheHome, Tom's Hardware…

Does the newly released SFOS v20 support newer fanless PCs containing the intel i225 ethernet chips, WITHOUT resorting to a VM? I suppose this is a resurrection of the question that was answered in the negative for v. 19.x last year in Does Sophos XG…

Hi all, I recently got my hands on a used SG135rev3 appliance and tried installing XG home edition on it. After installation, I see in the commandline (via HDMI) that the appliance has succesfully booted up, but unfortunately the LAN doesnt come up…

hi I have a Cyberoam CR100ing firewall (1.6.3 MR-4) in my hands that I got from my previous job and I plan to install the new Sophos XG home edition OS on it since it is the most compatible with the hardware today. What happens is that the Cyberoam cr100ing…

I have some questions regarding deploying the Sophos Firewall Home Edition. Does anyone have any recommendations on hardware to use and to avoid? I would like to look into something small and compact if possible. A plus if it's easily mountable…

Hi Everyone in the Sophos Community. I downloaded the ISO for the Sophos Firewall Home Edition-Free Version and used Rufus to burn it to a flash drive. I am trying to install it on my Dell Opiplex 9010 Desktop PC but when I boot to the flash drive it…

Hello, I am trying to install sophos for home use on my old Lenovo 720q on nvme and after installation is not booting Bios is in Legacy, nvme first to boot. My Hardware: CPU i3 Nvme 512gb 8 GB ram(i can boost to 32gb if needed additional…

I want to deregister suphos sg 330 from my account. I would like the device to be reset without a license. I would like to use them for home use.Resetting and reinstalling the firmware doesn't help.