Hello, I installed Sophos XG on the cloud. I can't access it from the web because it is port 2 WAN, and it should be the LAN, but I can't change it. Is there any way to change the zone from WAN to LAN? It's the home edition, so I'm not sure this is the…

I created a certificate based IPSec/IKEv2 Site-to-Site-VPN using the Sophos guides between two Sophos SG135 firewalls. One firewall runs on home edition (SFVH with firmware SFOS 21.0.0 GA-Build169 ) one runs on trial (SG135 with firmware SFOS 20.0.2 MR…

After running home firewall for many years, I decided it is time for an upgrade to the latest. The old version is v9. I downloaded and installed v20, and it is different so it took me a bit to figure it out. But when I try to restore a backup…

I have the latest Sophos Firewall Software Home 20 installed on my mini pc as well as on old XG 135w router and on both devices I experience issue with no DHCP reply for Wifi what using VLAN. - I have tested Unifi and Zyxel AP same issue - I have directly…

Hello, Since the XG Firewall does not have countries for IPv6, I have created my own countries based on published IPv6 address ranges which can be found here https://www.ipdeny.com/ I created a LAN to WAN rule to block access to a country and a WAN…

Hi, I tried to upgrade my home appliance (home license) from 21.0 EAP1 to 21.0 GA with the following error: 2024-11-18 11:16:20.459 GMT starting old version corporate db Starting conf database 1 2024-11-18 11:16:21.852 GMTLOG: starting PostgreSQL…

Apologies I know it's been mentioned before, but I'm in the process of moving from pfsense + to XG Home. Got a variety of loose ends to sort out and DNS over TLS is one of them. Is this forthcoming within the v21 release cycle? I'm sorting Wireguard…

I’m in the process of getting Sophos XG Home as an alternative to pfsense. I’m 90% there, but is there a way to do DNS Rebinding, particularly for plex? i don’t want to open ports as I accessed everything via a VPN with pfsense and it worked perfectly…

Hi fellow community members. I am trying to create a new local group on my Sophos XG Home (Running as Virtual appliance). Under the IPSEC remote access option. It is on disabled and greyed out. This is for both under the User category and also under…

Hello Sophos-Support, Can you please check the problem? Unfortunately the problem still in v21 GM exists. Intel X710 10GbE SFP+ (passthrough) not detected PCIe passthrough works smoothly with the software installer. Hypervisor: Proxmox 8.2…

Good evening, Back testing XG Home, does v21 support hardware acceleration for IPsec and SSL VPN tunnels? I have XG Home installed on a XG230 R2 at mo, I have a XG135 R3 that has pfsense + on it atm, so pending successful testing, planning on dropping…

Hi! I recently got a XGS 108 for home use, however, I am little lost on how to set-up my network now. Currently, I have an ISP modem acting as a bridge, then an ASUS router in a mesh wifi with an access point. The ASUS router is handling DHCP management…

Certificate request fails with secondary validation time out. I can see in the web server protection log viewer that the well known url is being requested with the unique value. I also briefly see that the temporary waf rule is created. Only thing to…

Hi. I have a problem with receiving network traffic in PROXMOX_DMZ. I want two networks to be available in this PROXMOX_DMZ: 1. DMZ NETWORK 2. DMZ VLAN 1721 My devices and the connections between them Incoming traffic to the microtik ISP -> PORT WAN/vmbr0…

Hi is it possible yet for Sophos XG V21 Home to be an openvpn client connection? Expect to cancel Virgin internet in December as they want to go from £23pm to £59pm. So I was considering using my 4G backup, but it’s CGNAT. I have tested openvpn cloud…

I successfully obtained 5 certificates from Lets Encrypt with th new V21 feature. I can use these in my web application firewall rules and they work fine. But in "Administration/Admin console and end-user interaction" only an uploaded wildcard certificate…

Hi, I am trying to get QAT support information on the current XG Home v21. The last document that mentioned QAT was version 18. Is QAT still supported? If so, what can be offloaded to it?

Hello, A Sophos Firewall Home User here.. I have been dealing with an issue that I am not sure how to tackle. I want to block access to all adult sites in my network, and even though the firewall categorizes the obvious ones in the right way, there…

Hi, I have a bizarre issue with the docker container and Sophos XG's DNS resolver. Let me lay out my setup first. I am running Sophos XG Home 20.0.2MR2 on a Dell R210 II. There is no IPv6 enabled anywhere. My docker host is Ubuntu 24.04 LTS and docker…

Hi, I moved to Version 21.0 GA (Home Edition) recently. I noticed that in control panel, no events in the log or counters are logged that X-Ops is doing anything: A configured third party threat list (abuseipdb.com) is working properly and blocks…

I have radius authentication working locally from the Sophos Firewall to the local radius server for both VPN and for WiFi authentication, however I am unable to get the authentication working from the Sophos Firewall to another radius server at a remote…

Hi all, im pretty new to the sophos firewall i noted that on the dashboard it showed an attack and also checked the logs whcih are both shown below. From this i can see that it was detected rather than blocked. Is there a way to set the IPS to block by…

Hello, I followed the links to get the firewall, got sent a serial number via email, but when I tried to download the ISO I got sent out to the trade compliance form, which then required additional verification which I can't perform because the link supplied…

Hi, I've got a used XG 115w rev3 and installed the Sophos XG Home Software Version on it. The issue I encountered was that after a successful installation of the SW image, I cannot reach the appliance to complete the initial wizard. When patched…

Hi There I recently acquired a second-hand XG115W. After wiping the SSD, I successfully installed the V20 HOME firmware on it. However, I've encountered this issue after the installation: Ethernet ports 2 and 3 do not function. I can see the activate…