Hello good Morning a question friends is the sophos XGS 116w compatible with the XG230 firewall? is it the same as a RED15w in terms of configuration? as I have several of these added to my XG230 it is added just like the RED one, I need it to create…

We have the following scenario: Sophos XG135 (SFOS 18.5.2 MR-2-Build380) Port 1 gateway to fibre internet Port 2 Gateway to VDSL Port 3 Gateway to LTE Port 4 LAN Clients Port 5 LAN Server Port 6 DMZ The XG connects multible IPSEC tunnels via Port…

Has anyone done one of these before successfully? I've had no problem with any of the Standard mode configurations, however this Transparent/Split one has given me a headache. I've even got a call open with Sophos and have had a lengthy call today were…

We have a remote employee utilizing wireless internet provided by their landlord. We would like to procure a wireless to ethernet bridge for the wired DHCP handoff to a RED 20. I am seeing some Cisco WET devices that could fit the bill. Has anyone had…

Hi everyone, we created a BO and connected this site with the HO over a RED60 without VLAN tagging. So far so good :-). Now we would like to enroll some AP's in the BO with a setup similar to the HO. In the HO, we make use of Unifi HD nano AP's with…

Hi, What to do? I have a RED20 working correct with Xg Firewall 18.x - when I connect a laptop in LAN port, receive correct IP address through XG DHCP server - can access the remote network I have a Sophos APX320 Wifi access point connected…

I'm running a XG firewall at the office (XG135 18.5.2 MR-2) and one at home (XG135 18.5.2 MR-2), both are connected with RED (Firewall RED client on the XG's). All is working as expected. I just bougth a second hands RED 50 to replace my XG at home…

Hello, I succesfully test a RED device on one XG Firewall, however I want to set same RED Device on a different XG Firewall, I know I have to use the unlock code to do so, and I did it, however when setting and connecting the RED Device I get a error…

I work for a healthcare provider. We are going to provide services for the schools in our county. I need to set up a small network (2-6 devices) inside each of the schools that can communicate with the home office. The school is providing internet via…

Hi Can anyone assist with a link or Documentation on the Recommended Red Device Sizing guide for XGS 3100 & XGS 4300 thank you.

Hello, i have sucessfully configured the RED20 Device to my XGS-126. I can reach any device, that is connected to my XGS Network. Now i need to configure the acess back to the devices that are connected to my RED Network. I can ping the RED20 Device…

Hey, I,ve got the problem that I can not ping the RED device itself but all devices connected via this RED device. I have firewall rules in place to allow this ping cross these vlans. Is there any specific setting in Sophos XG, like "Device Access…

Hello Guys I have a Red 60 and I can ping it from Sophos XG135 but not form any laptop form the main office LAN. I have even set the route_precedence to 1. VPN 2. SD-WAN Policy routes but it does not work Could someone help me out with this…

Good afternoon all, Recently I deployed a Fortigate firewall at our edge and replaced the Sophos XG 210 we previously used. However, I have a remote site connected via a RED device and rather than mess around with another box and IPSec VPN tunnels,…

Hi, I got an brand new XGS2300 Cluster (active-passive)at on of our customers which six SD-RED 60 connected. When making changes to one of the RED tunnels (every tunnel has two VLANs in access mode, drop tagged associated) the update of the interface…

Hi, I've problem UTM310 with RED60. the REDs (transparent/split) and another site i have sophos cyberoam ICMP ping forward is enabled. Ping from Client behind RED to internal is good and i can access any client but i can't access from side. I check…

HI I would like to deploy RED at 16 remote sites, I would like to know if Sophos XG 135 ( which is our client existing firewall) supports RED-50. Thanks

Hello all, looking for some help and guidance. I have one office with a sophos xg and 4 remote sites using SD RED 20 units. All 4 SD RED 20 units are connected back to the XG using standard/unified mode. No issues with getting this all connected.…

Deutsch (english below) Hallo zusammen Wir haben in den aussenstandorten jeweils ein RED. Wenn ich den Drucker in einem RED-Standort oder vom Hauptstandort an einem RED-Standort über Windows verbinden möchte, erkennt er den Drucker nicht automatisch…

This topic was discussed here but I found a way to make it work. However, this solution causes something else very important to stop working. The following problem originally exist. Based on Sophos SFOS 18.5.1 MR-1-Build326 When creating a new hotspot…

Hi All. Has anyone come across this before. I had a RED15 device working fine on UTM. I moved it to XG and it works fine. Try move it back to UTM and it does not connect at all ? Any ideas, its still working on the XG so I dont understand why…