Hi,
We have 2x XG310s in HA Active/Passive
Our LAN is currently on Port1 (1G Copper) on both devices
I want to configure and move my LAN IP Interface from Port1 to Port9 so I can utilise the SFP port instead.
Is there an easy way to do this? …
Hello everyone I want to know what monitoring software they use to monitor their FW XG, actually,, I want to monitor all logs from all our firewalls
Hope you help me
Thanks
Any idea when 1:1 SNAT will be implemented correctly from it's currently half baked implementation? While doing SNAT and using a IP range (.1 - .254), the translated IP is a completely random octet, which is not desired in our configuration as the remote…
Can someone please help me! I have been having issues lately with my Sophos XG 330 rev.2 Firewall. First off I have had a complete system crash where I had to completely re-install firmware (the system reboots to "fail safe mode") Next I keep randomly…
I have DSL modem from Centurylink that has one port using a static IP address that is connected to a Linksys Smart Router that has the Static IP address currently setup, i have tried to install the XG 115 using port 2 with the cable coming from the Centurylink…
Im trying to setup failover connections so that in the event of our WAN (P2P) connection fails the sophos auto fails over to our WAN (VPN) connection. the wan P2P connection also has static routes enabled so these would need to failover aswell.
Hello,
we have noticed one http traffic issue on Sophos XG 210 with release 18.0.4. We have defined a firewall rule which is allowing all services from LAN to (RMX) server.
Port1 = LAN zone
Port3.3353 = RMX server zone
When we try to connect from…
SO I created another LAN interface for my IoT Devices and everything is working as long as I am allowing the LAN int to access the WAN with an Any Any rule. I have decided to tighten up this rule and noticed that the firewall is blocking my LAN Source…
We have 3 lines
Line A: - has a fixed public Ip - is needed for authentication with MS services (Exchange365 and others). Certain requests to MS have to be initiated over this fixed Ip - is part of a VPN - has the lowest bandwidth
Line B and C - have…
Dear I would like to share a bad experience I had in a migration from v17 to v18. and I need to expose it because it was a small environment that could be circumvented but there are other giant environments that need to be migrated and I cannot experience…
Dear Community,
This is my first interaction and product purchased from Sophos, an XG125w firewall with the 4G module expansion. I thought the hard part would be the configuring of the firewall which in the end turned out to be extremely intuitive,…
Hi Guys,
I have issue that as you see in picture below.
1. I have MPLS connection between 2 Sophos one in HQ and second one in brunch.
2. User from brunch, using SSL VPN to access to HQ Servers, this one is working, for example they can ping the…
Our XG firewall is also running as a DNS server.
We have a device sending DNS requests to our firewall trying to get the ip for a malicious domain, and we are trying to identify the ip of the device sending the requests.
From what I can see XG…
Hi may I know once I set up the XG 430 HA and how to connect to the redundant core switch (Stacking Netgear) , thank you.
etc: create 2 lan ports and assign IP to each core switch?
Hallo Community,
ich versuche derzeit mein Netzwerk von außerhalb erreichbar zu machen. Da ich über einen DS-Lite tunnel verfüge, muss ich dies über IPv6 verwirklichen. Von meinem ISP wird mir ein dynamisches IPv6 Präfix zugewiesen. Da ich keine Funktion…
We are using Sophos XG135 and recently just upgraded to a 1gbps modem.
ISP provider have confirmed that direct connection we are able to achieve close to 900mbps up and down.
However, we did a speedtest for wireless connection, we achieve around 200plus…
After upgrading the firmware to SFOS 18.0.3 MR-3 now users are not able to access web services using local/Private IP addresses, only it works when NATted to the Public IP.
Could any one help on this please?
Hello,
I have been testing the use of clietless access VPN with a customer and we found that there's not info on the reports for this VPN. We are using those bookmarks to give access through RDP to some servers. Alls the bookmarks works and the users…
Hi Community,
After alot of thinking, trying and googling Im stuck, so here I am.
At home I run a XG 135 with the latest updates installed. The XG is in DMZ (to keep my parents network and mine seperated)
Clients within my VLAN just won't load…
Hi,
I intend to copy the entire configuration (ip alias, gateway ...) from a vlan interface to another physical interface, is it possible? My firmware is: SFOS 18.0.3 MR-3
Regards,
HB
I am trying to put my VOIP system behind our firewall. I would like to separate our data WAN from the VOIP WAN interface. When I did a test configuration the VOIP packets were being sent through both WAN interfaces causing audio issues. What configuration…
I have a ACT! server for our CRM. It is able to accept inbound communication for port 65100 but outbound is not routing. Communication was working fine prior to upgrading from v17 to v18. I have tried setting up LAN -> LAN firewall rules for the port…
Hallo,
ich hoffe jemand von Ihnen kann uns helfen.
Wir haben seit kurzem eine SOPHOS XG125 (SFOS 18) im Einsatz. Ich habe den SSL-VPN Zugriff laut Anleitung konfiguriert und kann mich mit dem Client auch wunderbar verbinden. Nun habe ich allerdings…
Hello,
I would like to filter only events for all IPs from a specific subnet - let's call it 192.168.1.0/24.
So in logviewer I would create a filter for Src IP starts with 192.168.1.
Now the log viewer is ignoring the terminating dot in the filter…