Hi there , relatively new to Sophos firewall however I currently have it setup at home feeding direct 100 mbit connection from the wall to my firewall with a switch that’s fully occupied under 17.16.16.1/24 ip range for a few devices and my wireless…

Good morning, I come to you today asking for some advice. I am really under the gun with revamping our entire flat network into a more optimized system. Being the single IT person responsible for multiple plants I am quite overwhelmed with what direction…

Hi everyone is there any way to diagose an optic SFP module on SFOS? I think about the infos you can get on a switch: - check if the SFP is recognized - get the Infos from the module (S/N, Type: SX,LX, LH...) - read the optic information like RX…

HI, i'm testing XG as Firewall for my VMs in dedicated server in OVH dataceter. I'm able to configure correctly the WAN port with IP Failover in XG. In Linux machine i configure the WAN link infconfig eth0 IPFAILOVER/32 route add GWIP dev eth0…

I got a new fibre internet at home. PPPOE is done with a Fritzbox to a Fibre Modem via PPPOE without any credentials needed. As to avoid double NAT i want my XG to do the PPPOE connection directly, but i have no way to leave user and pws empty. If i enter…

I have two connections from the same ISP that I would like to connect to my XG firewall and have both actively function. However as soon as both interfaces are connected, one goes down and inactive. Is there any way to have two WAN connections to the…

Good morning everyone, I'm having a problem doing a PPTP VPN between an XG S2100 and a Teltonika RUT950. I also submitted the question to Teltonika support who answered me after seeing the logs. They claim that the problem is that Sophos releases its…

Hi all, today I made an manual failover to the auxiliary device. On the auxiliary device the XFRM interfaces began to flapping. On both tunnel ends I had many interface up and down events (ervery few seconds). The IPSec Tunnel itself seems to be stable…

Hi, How many LAN interfaces does Sophos Firewall support? I am aware that the maximum no. of VLANs supported is dependent on the ethernet controller - see Sophos Firewall/Sophos UTM: VLAN limitations based on chipsets on network modules - however…

Hello, I refueled an XG125 Rev 3 with the home version. Everything worked with the stick, but I only have only 2 interfaces. All other interfaces are dead, with the original hardware ISO all interfaces work. Does anyone have an idea of what that could…

Hi We install SOPHOS XGS 4300 device. We having one ISP providers with Static IP address 103.20.30.41 to 103.20.30.45 Port 2 I configure Wan Port and Static is 103.20.30.41 Port 3 I Configure Lan Port 192.168.1.1/24 and DHCP enable. In this port…

Hey Team, I have tried to work this out from the forums but I'm simply not getting it! The XG has multiple WAN interfaces: - Primary with STATIC network assignment - Failover 1 with DHCP network assignment - Failover 2 with PPPOE credentials Network…

Hello, i have a problem on a customers site. The customer switched from Sophos UTM to XG firewall. In the past the customer ran into the problem that his network got to small. Because of ease they just add 2 additinal adresses on the LAN interface…

Hi, On October 31, 2022 Windstream pushed a software update to our VeloCloud device that caused our Internet to go down every 20 minutes. The problem was isolate to ARP packets that are sent from our Sophos XG firewall to the VeloCloud device. At firewall…

Hi @all, I'd like to disable a hardware interface with an API call, in this case I weant the WAN-interface to be disabled. Is this possible? I already managed to disable an VPN-Tunnel with this command: my-ip:port/.../APIController Account</Username…

Hi, I've set up a new VLAN (20) bound to the LAN hardware (Port1.20) with IP 192.168.20.1, and assigned it to the DMZ zone. If I run the policy checker using Firewall,SSL/TLS and web method, with the following parameters, it fails URL: dns://192.168…

Hi team! My WAN interface was stoped working, just give me information of not available. Other interfaces woring well

Why is not possible to create GRE tunnel on bridge-interface (WAN port + DMZ port ) ?

Hello, I'm having a problem with my "Interfaces" widget, I have three Wan interfaces and yet they are all "UP" but the widget remains orange. My wan on interfaces for gateway: 192.168.4.1, 192.168.100.1 and 192.168.4.1 and they all respond to the ping…

Does the XGS5500 support operation at 2.5Gbps of a 2.5GBaseT SFP? I have a client who has an SFP-2.5G-T from sf.com installed in their XGS5500 which is then connected over copper patch lead to a router with in-built 2.5GBaseT ports. At present the link…

Hi, I have assigned 5 IPs to WAN interface of Sophos XGS 2100 From LAN, i can ping all these piblic IPs. From public network, only 2 out of 5 of these IPs are pingable. very weird. Any idea?

Hi Team, I am trying to create an interface in the XGS firewall via CLI : #ifconfig Port1 172.16.1.1 netmask 255.255.255.0 up but here it making only interface UP without ip, I want to know how can give Zone here, so that interface can be up with the…

Looking at getting a VDSL SFP for the XG 230 Rev2 that has XG Home installed on it (not in use atm). Do we know what the p/n is etc and whether it'll work?

Hi all, setup is router -> Firewall -> Ubiquity dream machine. XGS2100 is configured in gateway mode (need to use SSL VPN), wan cable to port2, lan cable to (F1), lan cable is connected to an Ubiquity Dream Machine PRO. In the F1port there…

Hi Sorry for the questions this evening. I have a XG 230 Rev 2 unit spare atm, tbh I'm not currently using it due to power consumption and noise. If I get my house cat6 wired as I hope to do, then it will be maybe pressed into service along with Aruba…