Hello, I am using a Sophos XG firewall (Version 19.5) and I have 2 WAN interfaces on that (1 active, 1 backup in the WAN link manager). To have the backup line not unused, we use it for SSL VPN (which works without problems). The problem is, that the…

I've got a Sophos XGS116 at a colocation site where we host a bunch of servers for our clients. Currently on SFOS 18.5.2 MR-2-Build380 although I can update it before this changeover if needed for functionality for my request below. Otherwise, I was going…

I have implemented my sophos firewall in bridge mode. I have access to the internal devices, but I cannot access the Internet, what needs to be done to access the Internet? I was trying with a firewall rule but it didn't work.

Hi all, We will replace our ADSL connection by fiber connection So we have Echolife Echolife HG8245H5 /GPON Terminal I need to know how to configure XG Wan port with this " FTTH Modem", i don't know if this terminal is layer 2 or layer 3, or if…

I have installed Sophos XG but when configuring the WAN port, the Firewall does not recognize the network adapter. This a USB to RJ45. Do you know if there a list of network adapters that are compatible with Sophos XG?

Hi, is there an VDSL-Module supporting 250 MBit (from Sophos)? Should be VDSL2-profile 35b .. Thanks,

Hi, When I create a Tunnel interface, I am unable to find the xfrm interface in Network >> Interfaces. I can see the xfrm interface in the CLI though. How do I get to see it in the GUI as I need to use it in a Static Route?

We have a setup with 2 x XG230 configured with HA active / passive with PPPoE on PortA2. Primary Sophos PortA2 connects to ISP Primary router and Aux Sophos PortA2 connects to ISP Aux Router. Port A2 is set as monitored interface. ISP Primary router has…

Hi, I've moved to SFOS 19.5 from UTM9 and having some trouble getting my head around a couple of the concepts. One of them is the Zone/Network/Devices model that SFOS uses; What's the relationship between Zones, and Networks and Devices when creating…

Hi folks, my new RSP has assigned me a new /48 for internal use, how do I renumber all my XG IPv6 addresses? Ian

Hello, I have a problem with the backup link in Sophos. We received an LTE link that works and has the correct address set. The "Type" options were set to "Backup" and the "Activate on failure of" rule was set to the main link. The problem is that when…

Hi All I have sophos xg 750 firewall and currently I want to ad one public IP as an alias on the existing Physical port. So on doing that will interrupt the production environment ?

Hi all, User Kyle Sexson had this issue a while ago, too, but there’s no solution in his post - so… I have a set of VLANs running on a bridge interface. This works mostly well, but certain outgoing traffic will show up both on the bridge interface…

Hi, my provider ISP provide me a PPPoE Dual Stack WAN connection. Using a Linux PC is possible to get IPv4 and IPv6 IPs with the same PPPoE connection and works perfectly. In VM XG FW v19.5 Port 1 configuration is WAN with IPv4 PPPoE and works…

Hi there , relatively new to Sophos firewall however I currently have it setup at home feeding direct 100 mbit connection from the wall to my firewall with a switch that’s fully occupied under 17.16.16.1/24 ip range for a few devices and my wireless…

Good morning, I come to you today asking for some advice. I am really under the gun with revamping our entire flat network into a more optimized system. Being the single IT person responsible for multiple plants I am quite overwhelmed with what direction…

Hi everyone is there any way to diagose an optic SFP module on SFOS? I think about the infos you can get on a switch: - check if the SFP is recognized - get the Infos from the module (S/N, Type: SX,LX, LH...) - read the optic information like RX…

HI, i'm testing XG as Firewall for my VMs in dedicated server in OVH dataceter. I'm able to configure correctly the WAN port with IP Failover in XG. In Linux machine i configure the WAN link infconfig eth0 IPFAILOVER/32 route add GWIP dev eth0…

I got a new fibre internet at home. PPPOE is done with a Fritzbox to a Fibre Modem via PPPOE without any credentials needed. As to avoid double NAT i want my XG to do the PPPOE connection directly, but i have no way to leave user and pws empty. If i enter…

I have two connections from the same ISP that I would like to connect to my XG firewall and have both actively function. However as soon as both interfaces are connected, one goes down and inactive. Is there any way to have two WAN connections to the…

Good morning everyone, I'm having a problem doing a PPTP VPN between an XG S2100 and a Teltonika RUT950. I also submitted the question to Teltonika support who answered me after seeing the logs. They claim that the problem is that Sophos releases its…

Hi all, today I made an manual failover to the auxiliary device. On the auxiliary device the XFRM interfaces began to flapping. On both tunnel ends I had many interface up and down events (ervery few seconds). The IPSec Tunnel itself seems to be stable…

Hi, How many LAN interfaces does Sophos Firewall support? I am aware that the maximum no. of VLANs supported is dependent on the ethernet controller - see Sophos Firewall/Sophos UTM: VLAN limitations based on chipsets on network modules - however…

Hi We install SOPHOS XGS 4300 device. We having one ISP providers with Static IP address 103.20.30.41 to 103.20.30.45 Port 2 I configure Wan Port and Static is 103.20.30.41 Port 3 I Configure Lan Port 192.168.1.1/24 and DHCP enable. In this port…

Hey Team, I have tried to work this out from the forums but I'm simply not getting it! The XG has multiple WAN interfaces: - Primary with STATIC network assignment - Failover 1 with DHCP network assignment - Failover 2 with PPPOE credentials Network…