Hi everyone So the performance and interface symbols in my control center are red. The interface when i click on it shows the gateway ip as red. I have attached a photo. The performance was orange and now it is red. Can someone please help…

Hello, we are trying to get the Sophos Firewall (19.5-MR3) up and running in a public datacenter and to do this we need to change the assignment of zones to interfaces and statically configure the public IP address for the WAN interface. Since the admin…

I would like to see an easy way to move vlans to another port. This will help in moving a heavily used port from one port to another without having to delete the vlan and DHCP scope and recreate it. This would speed up moving vlans across ports. …

Hi all, I rarely work with Sophos Firewalls and haven't ever had to do much on them before, but having recently logged in to one I found that on the 'Control Centre' page that 'Interfaces' is highlighted orange. When I then select 'Interfaces' it…

Recently I have added multiple WAN interfaces to our XGS's. I just noticed that when I attempt to manage polices for this Group of XGS, that it just SPINS and I cannot access the group policy management. I can manage each member of the group from central…

So i'm a bit confused and could use some help. After running NMAP on my public IP for a sanity check i was greeted with ports showing open that shouldn't be available to the WAN port. I don't have any services checked on my local service ACL for WAN Starting…

LAN port 1 and the rest of the other 7 ports on xg135 not working. After turning the device on the interface ports only flicks green and yellow lights at first then go off. I have tried the following: 1. Hard reset on the device 2. Factory reset…

Dear Sir I have configured two ISP on two different ports of firewall providing the internet facility through Sophos Firewall. I am using the firewall load balancing features by assigning the weightage of 2:1 to both the ISP's. But load balancing feature…

Dear community members! We are planning to insert an XGS firewall into our existing network infrastructure with multiple WANs. This is the current setup: Three WAN routers from different ISPs with fixed public IPs are connected to a multi-WAN router…

https://doc.sophos.com/nsg/sophos-firewall/19.5/help/en-us/webhelp/onlinehelp/HighAvailablityStartupGuide/HAConfiguration/HAQuickHAConfigureActivePassive/index.html#configure-ha-on-the-auxiliary-device (Optional) Select ports to be monitored : You can…

Will any admin who is not connecting the physical MGMT Port (there are a lot of reasons for), see this warning every time for the rest of his life? At least provide a "yes, I do NOT use the physical MGMT Port, it is all OK" button please...

Hello, Can I have PIM-SM and IGMP on a interface in the same time? I have a problem with IGMP on interface with active PIM-SM neighbour (pim-sm router). In the presence of a PIM-SM neighbour, IGMP is inoperable for another destination. Is this behavior…

the UTM had a way to monitor UPS. is this no longer available in XGS?

Hi, we have sophos xg-210 one LAN port utilization is high i have attached monitoring tools screenshot please check. model-XG210 Thanks satya

On our XG430 firewall we have some interfaces only the active ones are ~40 VLANs, ~40 REDs, ~30 virtual WiFi networks and adapters, ~10 physical interfaces Currently I monitor CPU load from time to time. Unfortunately, due to all graphs are preselected…

Hello, I still try to preconfigure the XGS for migration from SG. L2TP, IPSEC-VPN with RADIUS and AD-auth is working. IPSEC tunnel to our branch is fine. Now I want to preconfigure all public IPs and their DNAT/SNAT rules. Actually I am stuck…

XGS136/SFOS 19.5.2 Is it possible to use an alias WAN IP other than the firewall's IP with the SSL VPN? I'm setting up the XGS to replace an existing production firewall, and using an unused LAN and WAN IP to do it. My plan is that on migration day…

Hey Team, One of my end customer having issue in FW while upgraded SFOS 19.5.1 --> SFP ports/interfaces couldn't respond or stopped working and ethernet ports are working fine. XGS3100 (SFOS 19.5.1 MR-1-Build278) Expecting usual support from my…

Hi all, Is there a possibility to install a Flexi port module to an existing HA Pair without switching off both firewalls at the same time ?

Hi All, I recently added IPv6 support to XG FW and something says not right. I have pubic v6 address on WAN link, 2 private ranges on LAN and DMZ . I am using router advertisement for IPv6. The FW rules show traffic on v6 both directions, The v6 test…

Hello all, I have a few questions for the sophos firewall solution in azure. I followed the guide setting up the firewall with a WAN and LAN Interface. WAN is 10.0.1.0/24 with 10.0.1.4 as NIC private IP and a public IP assigned by Azure (example…

Hi everybody! Now we have a second WAN link (DHCP) and I‘m following the instructions: https://doc.sophos.com/nsg/sophos-firewall/18.5/Help/en-us/webhelp/onlinehelp/AdministratorHelp/Routing/Gateways/RoutingConfigureGatewayBalancing/index.html …

I use a ZBOX CI 323 with XG 17.5, which works flawlessly, but I can't upgrade to the newer 18.0, since this version will not recognize the second LAN port on the device, which is used for WAN access. Using a USB LAN adapter also won't work. Anyone have…

Hi, I have the same question make into the UTM Firewal Forms postet, but don`t get a answer. So I try to post my problem here into the english Forum. I have a question about the Sophos Firewall and specifically the bridge there. I have virtualized by…

Good day everyone. I need to configure something on my XGS136 and can't seem to get it down. I have a 1gb/1gb fiber coming into a vendor device currently. I am going to move it to PORT4 of my Sophos using a public IP, and then need to share it back…