Hi all. I have a simple home network like internet > modem > SG115 firewall > switch > home LAN. In home LAN there is already a wireless mesh in bridge mode. The SG115 acts as the router and DHCP server. All wired and wireless devices work as they should…

Hi All I am trying to add a second WAN port in Sophos Firewall (XGS126 (SFOS 19.0.0 GA-Build317) but when I add the IP address, net-mask, gateway ip then I press Save and then Update interface - I get this error: "ip address lies within the leased ip…

The failover rule for a WAN link only allows for failover to "any available gateway." What if I want it to fail to a specific gateway, one that is active all the time? I have 3 WAN connections--these are ALL active connections ALL the time. Fios 1000…

We have an Aruba 2930M switch with 2 SFP+ ports as a LACP trunk connected to a Sophos XGS 4300 with 2 SFP+ ports combined as a LAG. We have several VLAN interfaces setup. I am unable to pass any traffic through to the firewall. If I break up the LAG and…

Hi guys There is one thing that caught my attention, What does Received drops mean? Thank you

Hello everyone here i check documents and dont found how to do this. I tried to did Ethernet card test XGS but i found this article https://support.sophos.com/support/s/article/KB-000036345?language=en_US&c__displayLanguage=en_US and saw dont…

I have Ports 2 and Port 4 configured as WAN, both active with weighting of 1. Both are connected to Comcast BUT separate internet connections, one is from my house, one from next door. It appears by Speed Testing that both are passing download traffic…

10GbE Fiber Transceiver Short Range is compatible with Cisco Meraki series or not

Greeting SOPHOS Comunity, I am looking for some help configuring routing on a Sophos XG 135 SFOS 19.0.0 GA-Build317. I don’t work on firewalls often, so I apologize if some terms are incorrect. I did find https://community.sophos.com/utm-firewall…

Hey, I am trying to find a way to send the WOL packet to computers connected to my XGS116. I have a bunch of work stations Intel Nucs on VLAN100 and some servers etc on VLAN200. I want to be able to turn them on remotely via WOL. The issue is, I…

Att fiber the wan interface is a 5gbe to a 10gbe card on my firewall. However it is not negotiating a 5gbe connection; rather only 1gbe. Anyway to enable 5gbe for this connection? 10gbe is available as a manual selection, but not 5gbe. Using an intel…

Hi folks, early this morning my Australian nbn connection failed. When restored the internal networks were not able to access the internet even though the wan status up. The issue being the XG did not request a new a new address. I restarted the nbn…

How can I get more ports on XG 230 if they are full?

Hi - I have a Sophos XG 135 and I have set up two different networks with different Gateway IP addresses. Port 1 uses 192.168.1.1 Port 8 uses 10.150.121.1 Port 2 is the WAN port I would like devices associated with Port 1 to be able to communicate…

I mistakenly made the Port2 interface my backup WAN, and Port4 my primary. As a consequence, the SSL VPN always prefers Port2 first, which is not as fast or stable, so I have to edit the user VPN config to move up the Port4 WAN to first in the config…

We have two lease line links configured on Sophos XGS 3100 firewall out of which the link of one of the lease line link goes down automatically after every 3-4 hours that too after changing weight of lease lines or changing fail over rules. Looking for…

Hi, I thought creating a Bridge on XGS-136, for example, creates a "switch" between bridged ports, but either I do not understand principle, or reality does not follow the principle - I found no, bridged ports do not behave like switched ports. For…

Hello, I have some issues with the management port which is in the same network as a management network that I want to "hide" behind the firewall. I changed some routing (on 10 GBit Port) with resulted into two interfaces on the firewall in the…

Hi, we recently replaced a UTM firewall with a XGS126 (SFOS 19.0.0 GA-Build317). We haven't changed anything else, the network config is the same. On this site we have a 10Mbps WAN link and two 2Mbps MPLS links (active-passive). We are ICMP monitoring…

GREETING!!! 1. I have site-1 and site-2 with there own sophos xg firewall connected to wan link on port-8, port-1 is on lan, and port-f1 uplink is connected on both sides. so what rule should i create to bypass the traffic from site 1 to site 2…

Hi all xg sophos FW Please look at picture below I don't know how can i read this config I know it's LS link, but there are 3 ip adresses: 01 private configured with its GW, and 02 others ip public (real ip). When you edit these 02 ip adresses…

Someone has a hint: I can't remove the network settings from a base interface on which Vlans are configured. At first I thought this configuration is not possible, but it is possible to configure it like this. To make it clear to images with the…

The following is the error in firewall log which showing RX State: packets errors:8 dropped:58662, please help to solve this issue. port 1 UP BROADCAST RUNNING MULTICAST RX State: packets:169291044 bytes:41103398907 (38.2 GiB) errors:8 dropped:58662…

Hi, we have 3 HA Active/Passive Clusters with XGS136. They all have Port10 as dedicated HA Port and are linked with 1m patch cables of good quality. All 6 nodes show dropped packets and some also show port errors on Port10 for RX only. Some of…

Hi All, When trying to configure the PPPOE i'm getting this error " Remote message: User not found." but i'm sure the user and password are working fine, is there something i can do? /Thanks pppd 2.4.7 started by root, uid 0 PPP session…