Hello, I still try to preconfigure the XGS for migration from SG. L2TP, IPSEC-VPN with RADIUS and AD-auth is working. IPSEC tunnel to our branch is fine. Now I want to preconfigure all public IPs and their DNAT/SNAT rules. Actually I am stuck…

XGS136/SFOS 19.5.2 Is it possible to use an alias WAN IP other than the firewall's IP with the SSL VPN? I'm setting up the XGS to replace an existing production firewall, and using an unused LAN and WAN IP to do it. My plan is that on migration day…

Hey Team, One of my end customer having issue in FW while upgraded SFOS 19.5.1 --> SFP ports/interfaces couldn't respond or stopped working and ethernet ports are working fine. XGS3100 (SFOS 19.5.1 MR-1-Build278) Expecting usual support from my…

Hi all, Is there a possibility to install a Flexi port module to an existing HA Pair without switching off both firewalls at the same time ?

Hi All, I recently added IPv6 support to XG FW and something says not right. I have pubic v6 address on WAN link, 2 private ranges on LAN and DMZ . I am using router advertisement for IPv6. The FW rules show traffic on v6 both directions, The v6 test…

Hello all, I have a few questions for the sophos firewall solution in azure. I followed the guide setting up the firewall with a WAN and LAN Interface. WAN is 10.0.1.0/24 with 10.0.1.4 as NIC private IP and a public IP assigned by Azure (example…

Hi everybody! Now we have a second WAN link (DHCP) and I‘m following the instructions: https://doc.sophos.com/nsg/sophos-firewall/18.5/Help/en-us/webhelp/onlinehelp/AdministratorHelp/Routing/Gateways/RoutingConfigureGatewayBalancing/index.html …

I use a ZBOX CI 323 with XG 17.5, which works flawlessly, but I can't upgrade to the newer 18.0, since this version will not recognize the second LAN port on the device, which is used for WAN access. Using a USB LAN adapter also won't work. Anyone have…

Hi, I have the same question make into the UTM Firewal Forms postet, but don`t get a answer. So I try to post my problem here into the english Forum. I have a question about the Sophos Firewall and specifically the bridge there. I have virtualized by…

Good day everyone. I need to configure something on my XGS136 and can't seem to get it down. I have a 1gb/1gb fiber coming into a vendor device currently. I am going to move it to PORT4 of my Sophos using a public IP, and then need to share it back…

Hi, I have a virtual Firewall v17.5 on a dedicated OVH ESXi Server. the WAN gateway is not on the WAN subnet This article explains it quite well community.sophos.com/.../using-xg-on-ovh-dedicated-server---general-routing-issues will it still work…

During HA-Rebuild and Upgrade to 19.5.1 I noticed a log in System logs: "PortA4 up" on the peer node at a time when it was unexpected. I then noticed on the physical interface, that the LED of that Port were off while the other 3 were blinking. It…

I have a Sophos XG 125 Firewall and recently after updating the latest firmware, I'm having an issue with WAN port of firewall. The firewall's WAN port does not update the IP address automatically. I have to unbind the port and bind the port again to…

Hello, I created a VLAN for my WAN interface. I see the IP in my FritzBox but the Gateway in the Sophos XG Home is offline. The ping check under "diagnostic" failed, too. Fritzbox Network Interfaces Gateway

Hi! I have Sophos XG106 rev.1 with home license activated SFVH (SFOS 19.5.1 MR-1-Build278) . Every few days the gateway/wan port goes down, attached log bellow: -- cd /log tail -f dgd.log NOTICE Mar 17 09:45:33Z [5495]: Executing : <gateway…

Hi there, I have one question related on the DSL Module , we configured everything like it should be - the connection works fine. But we have a small issue, that it shows the interface under Control Panel / System always as down. I remember something…

I need to support to configure a network. I have one ISP connection. ISP Provide us one primary IP, One secondary IP, One Data link IP and one Public IP. Now I need to configure our firewall before the router. p2p primary ip: 10.255.191.149/30 p2p…

In preparation for a Network upgrade (which we are also re-subnetting the entire network) I'd like to connect our new core to our XG 550 on a newly installed 10G port on a separate subnet. The existing is on a 1G 10.10.x.x /24 the new will be on 10.16…

WAN interface keeps going down every one /two Hours or so days. It started earlier this week and I can't find a reason why it happens. Once I reboot the router, it comes back up.

Hi all! Quick question regarding XGS 126: MTU is a property of the physical interface. If I want to reduce the MTU for a VLAN I have to do it on the physical interface. By adjusting MTU value I seem to lose the VLAN interface and the associated dependencies…

Hi, I would like to remove an interface of a LAG (HA AP Setup with 2 Nodes, XG310 (SFOS 19.5.0 ). I removed port8, clicked save, then the XG rebooted and the 2nd node became active. There the interface was still present. A renewed reboot back to node…

Hey, I am stuck with removing an interface from br0 on XG115w (SFOS 19.5.0 GA-Build197) I was trying to remove one interface from br0 and apply changes. Now I can not edit any details of the br0, the UI stuck in an infinite load cycle when I open…

Hi, It is possible to connect XGS3300/4300 to core switch with RJ45 SFP+ ASF-10G-T transcievers to get 10Gb/s speed over cooper? Any other transciever option, on link listed below I can only find this option for XG, not for XGS models? Has anyone tried…

Hi Community, is there a way to trigger a poe power cycle on poe ports on xgs firewalls. This would be very helpful to reboot a poe device remotely. Thank you. Kind regards, Chris

LAN LAGG (NON LACP) Active/Back-up Stops working after 5mins. I have to unplug one of the links for it to start working again. Until i unplug one of the links, can't ping the XG, get online and the SOPHOS Wifi stops working..... Basically the LAN…