Hello, I installed Sophos XG on the cloud. I can't access it from the web because it is port 2 WAN, and it should be the LAN, but I can't change it. Is there any way to change the zone from WAN to LAN? It's the home edition, so I'm not sure this is the…

Dear all, I am facing a problem that my WAN Port always showing RED and i could not ping the WAN Gateway. At the same time, the same line with the same Static ip address is working in my laptop / nearby desktop without any problem. Kindly let…

I'm trying to configure an SSL VPN. Our WAN subnet has 5 IP addresses, with 4 aliases set up for the additional IPs: Port2 Port2:0 Port2:1 Port2:2 Port2:3 Currently, I have a web server running on Port2:0 . I want the SSL VPN to run…

Hi all, I created a new alias interface but missed on digit, so the address doesn´t belong to a existing interface configuration. Now I cant delete that alias because its not showing up in gui. Is there a way do get rid of that alias via console?

Hi There I recently acquired a second-hand XG115W. After wiping the SSD, I successfully installed the V20 HOME firmware on it. However, I've encountered this issue after the installation: Ethernet ports 2 and 3 do not function. I can see the activate…

Hallo Zusammen, ich habe eine Sophos XG135W. Auf dieser läuft XG Home. Nach meinem gestrigen Neustart, starten nun nicht mehr die LAN Ports. Beim starten leuchten diese kurz auf, danach gehen Sie aus und haben auch keine Funktion mehr. Weiß…

HI How can i check the interface counters for WAN interfaces in the Sophos firewall ?

we have reinstalled the firmware for the firewall. and port 1 is not working it was damaged. we are trying to configure port 2 or 3 as LAN via the command line When we try to use interface configuration it is not allowing us to configure port 2 , we…

Bonjour Je dispose d' une double carte intel 10g et utilise le firewall xg en version virtualisée. A l' heure actuelle le débit est bridée a 1g et les paramètres semblent grisés. Est il possible de basculer et forcer zn 10g

Hi, what would be the proper way to configure different WAN ALIASES for outbound traffic, for example in this manner: LAN users would use WAN Alias 1 for browsing and accessing web LAN2 users would use WAN Alias 2 FreeWiFi users would use WAN…

Hi everyone, I am using a Huawei 3372 LTE stick on my SG-125 with SFOS for a couple years now. It is configured in DHCP mode as a failover WAN connection when the main connection goes down. Up until now this worked as intended but after upgrading the…

How do i remove the Physical Ports 5 and 8 in a XG 115 firewall from cli? After a restore of a XG125 backup into the XG115w i have these ports, they should be pseudo ports and editable. But they are not..

Looking at IP Hosts like #Port2 or ##ALL_RW, they are dynamic IP addresses, correct? So if Port2 is my WAN port and the ISP changes my IP (via DHCP), wherever #Port2 is used in any rule will automatically be updated instantly so that the rule still applies…

Hello: I have a WAN port (Port 2) that is connected to our ISP with an IP block of 65.170.xxx.xxx/29. We have another block of IP addresses from the same provider at 63.162.xxx.xxx/29. Both come in thru the same ISP router (Cisco 4300). There are 4…

Hi all, can someone provide a hint, how to access a device where all LAN-Interfaces are "tagged" and "LAG"-ports? I've restored a migrated config and now the only untagged port is the WAN-port (can#t ping or access these port) I am able to access…

Hello, I try@home to migrate from UTM zu SFOS. On the good old UTM there was only one LAN Interface. This was the gateway for some PCs. At the network configuration on the UTM, I configured the real-router-getway as gateway in this one UTM NIC. It…

Hello Community, I am currently in Poland setting up a second S2S tunnel and I am struggling with the fact that the xfrm interface of the tunnel cannot be found under the interface to which the tunnel is bound. What am I doing wrong? Attached are some…

Hi all, any hints to configure mobile WAN as backup line? wired WAN is default but when line is down mobile WAN should jump in place. Mobile WAN must be turned on or not? WWAN Interface must be to automatic or manual? Thanks for help …

Hello!! In my home network, I have a mini PC with two ports running Proxmox and a virtualized Sophos Firewall Home Edition. I have purchased a mini PC with four ports to replace the one I currently have. While I wait for it to arrive, I decided to…

Hi, Is there a limit to the number of IP aliases per interface?

Hello everyone, I’ve included my home network diagram and Sophos configuration below. After setting up Sophos Home (on ESXi) in bridge mode with VLANs, I assigned a static IP address of 192.168.11.10 to the bridge port. However, this IP address cannot…

I need some help to understand why this firewalls IPv6 gateway is constantly reported as failed. It's XGS126 with SFOS 20.0.1 Because of that Gateway errors I reconfigured it from being an active gateway to a backup failover gateway only. I have…

Hi, I'm currently preparing our new XGS3300 to migrate from our XG310 which is soon end of life. I've done a Config Backup from the XG310 and applied it to the XGS3300 which was successful apart from the XGS3300 MGMT Port is now disabled. Is there…

Hello, I have Sophos SG 330 Rev. 2, completely new. I have used a USB installer to install the community/free edition of SFOS. The installer went ahead correctly, installing OS on the local SSD, and the appliance rebooted. After I saw that the appliance…

Brief description of my setup: WAN1 is a hardline connection. WAN2 is a cellular 5G connection, using a standalone antenna and modem. SD-WAN 1 is configured for general internet traffic, where WAN1 is the default and WAN2 is failover, using TCP…