Hi Team, I recently install FW on VMware but issue is the login web page is taking too long to load. Using ssh I can easily and quickly go to the device setting but managementip:4444 is taking too long(20-30mins) to load. I used all the browser but…

Good day to you all. Am looking for some assistance and tips on deploying XGS firewall in azure. The current setup, we have 2 servers that are currently deployed in azure and we would want to protect them using XGS. Currently users RDP to the servers…

Hi Guys, i recently acquired a sophos XG 106, The issue is that whenever i connect a Access point to the LAN Port such us ubiquity or any other one. it constantly drops the connectiion every 5 min or less, this behavior happens on every single port, i…

Hi, I just upgraded my internet to 1gbps down and 50mbs up. Running a speedtest from a workstation yields 200/47. I disabled IPS and it slightly increased to 270/47. I ran multiple CLI based speedtests from both geographical close servers and…

Today I got a brand new sophos xgs 116 firewall. This device has an absolutely loud and annoying fan-sound that crashes my ears. I cannot remember, that older xg sound similar. Does anybody else experience this high and loud fan with new devices…

Manual indicates a Power issue, red light would illuminate below power supply. Both power supply lights are green. Removed one at a time and reboot, keeps beeping continuously .

I am currently trying to reset a Sophos XGS 107 firewall, as the port configuration is unknown to us and we cannot access the interface via the GUI. After a deeper research I found out that for the hard factory reset of this firewall you have to press…

Hi , Yesterday my Firewall XGS 107 was working normal, but today at the morning stops working , it has just status led and power led on, when i restart the sophos , the blue led just turn on a few secs, I can listen that at least the fan its working…

I have two sites both protected by a SOPHOS device. From my UK (UTM 9) site I have a point to site Azure VPN working to a file share in my Azure virtual Network. Working great! It is secured with a self-signed certificate chain. I have colleagues working…

Good day XG 135 was working fine, then went off suddenly. When l try to access it via command line it shows grub rescue> grub rescue> What could be the cause of this . We trying to boot a new firmware

Running SFOS 19.5.2 MR-2-Build624 on a ESXi 7.03 server. Things have been running fine for a few months. I upgraded from UTM. Suddenly the CPU utilization went from 5% to 99% at about 21:45 GMT yesterday. I have rebooted several times. It goes down a…

Hey there, we just bought an Flexiport Module with 4x SFP+ Ports to connect our XGS2100 with our Backbone Switch (Cisco Nexus 9000 C93180YC-FX). We use FS SFP-10GSR-85 Modules on the Sophos side, and FS SFP-10/25G-CSR-S Modules on the Cisco side…

LAN port 1 and the rest of the other 7 ports on xg135 not working. After turning the device on the interface ports only flicks green and yellow lights at first then go off. I have tried the following: 1. Hard reset on the device 2. Factory reset…

Hi, Is there any way to check the Sophos XGS firewall temp? Firmware V19.5.MR1 TIA

It is possible to install Sophos Firewall OS in Proxmox with the ISO image, or is just possible with de KVM image?

Hey guys, we have trouble with several models (f.e. XGS 3300 and XGS 4500) and the Harddisks. Mostly when i upgrade the clusters the problem comes in front. When the devices are running we expect the logging/reports is not working, firewalling…

Hi everyone, I am currently trying to get a Sophos Firewall working as a VM in gridscale. It boots up in failsafe mode however, saying it doesn't have any interfaces. I have assigned interfaces to the VM. How do I add an interface via CLI or configure…

Has anyone ran into the Rack mount kit for the XGS 126 holes not lining up. If you screw in the front, the rear 2 do not line up. If you do the opposite, the front hole will not line up. See attached picture as an example I double checked and we do…

Is there anyway of getting the UK plug connector for the ADAPTER TECH ATS036T-W120V PSU?

I'm running Sophos XG in a VM on my QNAP. When there is a power failure, my QNAP suspends my VMs and shuts down. Upon reboot, it resumes all the VMS and uses virtio-serial to sync time. Since Sophos XG doesn't have support, the time is off, which doesn…

Hello! I was wondering if Sophos would sell those modules ( interfaces) when someone buys a firewall. 1 - 25 Gbps SFP28 2 - 40 gps qsfp + Only asking because i Could not find it in sophos firewall datasheet. (modules) If someone could help- me.…

If I run the XG Firewall in azure Microsoft Azure Marketplace as PAYG licensing, am I billed for the hourly cost of of the PAYG license if the Sophos VM is in a stopped state? I understand in a stopped state i am billed for the azure vm cost, in a stopped…

Hello, I'm founding difficulties determining if the XGS 3300 firewall can support a 2gbps throughput in a HA cluster with 2 equipments. Can someone help me? Also if it has a firewall throughput of at least 37 gbps; a ips throughtput of at least 13 gbps…

Does anyone have the SG135 Rev3 PSU SKU number for a UK PSU? Looking to potentially purchase one if not too expensive.

Hi all, Since SFOS 19.5.2 MR-2-Build624 we now have 3 customers so far, some with HA setup and others with stand alone, that the firewall suddenly stops and all the network interfaces are off. The LCD panel on the front shows fw status, but none…