I recently started using XG firewall on my home network. I just had a 600/35 connection installed from my isp. I also have a 200/10 connection from the same isp if I connect my router directly to my network I get the said speeds just fine. When I connect…

I apologize because it seems like there are quite a few conversations about Hardware for XG Home, However most seem old (3+ years). A lot of SBC computers are hitting the market and seem to be just as useful for XG Home. That said, I'm hoping someone…

Hello community, as I am starting to work with Firewall and off-side server, I rented a relatively small server having only 2GB of RAM. Is there a way, to get the ISO Image for the XG Firewall to run this on to install it directly on the INTEL hardware…

Hi guys By September/December I can have both, but one by September. I was hoping for these two configurations done, let me know which appliance I should get from a security standpoint. NBN Modem > XG106W (Fullguard Plus) > Forcepoint NGFW 110…

I downloaded the latest release of Sophos XG Home 18.0.1_MR-1-Build396-396 on my HP 800 G1 tower CPU core i5 4570 and 8 giga ram with HDD segat 160 giga Intel(R) Ethernet Connection I217-LM LAN bulti in adapter tp link TG-3468 lan PCI express …

I performed a fresh install of SFOS 18.0.4 on a mini-PC. Everything went fine until I registered it and initiated license sync. As soon as I did that, the firewall crashed and will not boot. I connected a monitor and when it gets to the point that it…

Hello I am trying to install sophos xg on a lenovo thinkcenter M 93p computer with intel core i3 processor with 8 gb ram. However, this computer only has a network card, I installed an external USB gibabit card, but at the time of installation, Sophos…

Hi, I am currently running Sophos XG home on my Qotom device. It was working perfectly until I upgraded to 1gbps connection. Now, I am able to get maximum 300-500mbps speed and the CPU is running at it's maximum. So I am planning to upgrade my hardware…

Hey all, I'm in the middle of trying to install Sophos XG Home Edition. I have the following download: SW-18.0.1_MR-1-Build396-396.iso Using Rufus to image the ISO to USB. Edited the boot sequence to USB first. I load the USB and reboot the…

Hi everyone, I'm in the market for a mini PC unit to run XG Home on my network and I've come across a few worthy contenders (in terms of price, having quad-core CPUs, etc.) but they seem to all be running some form of Realtek NIC. One unit in particular…

Hi All Apologies if this has been asked before I have a qotom hardware with 4 Intel NICs running on Intel Celeron J1900 processor. I was running OPNSense on it for many months and wanted to try out the XG Home edition version 18.0.1-396. I tried to…

Looking at selling my i3-6100T and swapping it out for a i7-6700T , anyone running one of these CPUs on their XG? My XG is currently running on a Xeon E3-1240L PowerEdge. Need to have a clearout of kit, so prob will sell off the surplus kit, as…

Sophos XG is currently installed on a 60GB SSD disk (not in the system atm), I have a 120GB SSD I was going to install into the Dell PowerEdge, I have a hard drive duplication device, is it possible to clone the 60GB to the 120GB and then use GParted…

Got a Dell PowerEdge R220 that has dual Broadcom 5720 NICs on the board, anyone using these NICs for Sophos XG? About to rebuild Sophos XG on the Dell PowerEdge, it's got Untangle on it atm. I have two spare PCI Intel NIC cards too 4 port 1000/PT and…

Hi, Does anyone know if XG Firewall supports Nvidia SmartNIC's ConnectX-4 and ConnectX-5 ?

I am trying to install the software version of XG Firewall on the Dell R210 II E3-1260L 16GB RAM but receive the error "appliance not detected". Is anyone else having this issue or any workarounds that could help get the Firewall installed?