Do I modify existing or delete/add External (WAN) Interface with new Internet provider?
Greetings Sophos UTM Community,
This is my first post and I'd like to ask a basic question.
We are switching Internet providers for our small business, Cable to Fiber. I have a Sophos SG-210 firewall.
My question is do I modify the existing External…
After a recent network upgrade, we want to be sure that VPN traffic is being directed to the highest capacity circuit
Current Sophos hardware: SG210, firmware 9.413-4
Prior to a week ago, there was one broadband WAN interface connected to the SG210; speed 120Mb up/15 Mb down. An additional fiber optic WAN interface was added: speed: 100Mb up/100Mb down. These two WAN…
TPG Fibre 400 on a SG210
I have just upgraded my internet to the TPG Fibre 400mbit service.
However i can only get a maximum output on speedtest.net of 260mbit via my SG210.
The Firewall is fully patched and uptodate.
The service works as it have been tested directly…
Utm 9 home edition setup
Hi Guys
I am new to UTM's and trying to learn. I have installed UTM 9 on vmware workstation. Please guide me for network adapter settings. I've tried all the settings bt none of one worked for me. if i setup two network interfaces for my vm machine…
WAN Interface bouncing multiple times per day
What log file will give me the best information into why this is happening?
How to configure RED50 with one connection to internet and one connection to private WAN?
We have multiple manufacturing sites within the US, each site has its own T1 for private WAN and its own internet connection as a backup to the T1. Despite pulling as much traffic out of the private WAN as possible, we have grown out of the T1's (shocker…
Needing to reboot the UTM
For years, whenever I had a cable modem issue, and I called for tech support, I'd quietly chuckle when they would ask me to unplug the power to my router. However, a few weeks ago, that was what it took for my Internet to come back (Not literally removing…
SSL VPN with 2 Internet Connections and 2 Hostnames
Good Morning Everybody,
I need your help...
I have 2 difference Internet Connections. One from A1 (slowly....) and a twice (faster,backup) LTE Connection.
The UTM is configured with Upload Balancing beetween this two Uplinks.
I also have a…
Dual WAN causes switch loop/broadcast storm
Hello,
I work for an ISP. We have a customer that is trying to use the Sophos UTM9 SG105 on our Network. They want to set this up between their current cable connection and the fiber connection from us. They uplink to us via a Mikrotik CloudSwitch…
Dual WAN without Uplink Balancing
Hi
Sorry for the novel, but I wanted to give details. What is the best way to enable multiple ISP uplinks but without the uplink balancing or having to configure multipath rules? I have 2 WAN connections, but obviously when you set a default gateway…
QOS for virtual webserver and WAN
Hi,
does anybody has experience with this? Since we activated QOS for WAN the website we have in the Webserver Protection is really slow.
Maybe somebody has a best practice for it? It tried a few things but there was no improvement...
Thanks,
…
Dual WAN, VPN Listening on WAN1, WAF listening on WAN2
Hello,
I hope someone can help me with this issue as I am completely confused with this. I have configured 2 WAN interfaces both with there own external IP's. Both WAN can ping out to 8.8.8.8 so i know the internet connectivity is there. However here…
WAN connection stops working/routing but interface still UP/UP. Have to disable and re-enable to allow traffic again
Firstly my UTM is up to date. Whether that is a good or a bad thing is uncertain :)
I have a cable modem in bridge mode with three connections to it. Each connection gets a public IP address from my ISP. One of these is the WAN connection on the UTM…
Different firewall rules per WAN link
We have a Sophos UTM SG 125. We have two WAN links, our main one through our ISP and a 4G modem link setup in an active / standby configuration. (Uplink Balancing and Uplink Monitoring)
When our main ISP connection fails, it fails over to the 4G cell…
Per outgoing interface firewall rules
We have a Sophos UTM SG 125. We have two WAN links, our main one through our ISP and a 4G modem link setup in an active / standby configuration. (Uplink Balancing and Uplink Monitoring)
When our main ISP connection fails, it fails over to the 4G cell…
How to get the IPs of (all) connected REDs via command-line?
Hi
is there any command to get the IPs of the connected REDs via command-line? I already tried
cc get red
but it only shows the internal name of the REDs, certs and so on, but no IPs.
Regards Rolf
RE: Where to check the Website accessing log for Domain PC
Hi Bob,
you are right , i didn't clear myself in my post. so the Thing is , I have Domain and All the Computer are Routed through Office Interface and later on the External Interface IP address.
my Traffic came from Inside and accessed Outside Server…
How do I configure AT&T EaMIS / WAN subnet routing?
Hi all,
At one of our new locations where we installed a new AT&T fiber optic internet circuit we received different routing and IP information than for our other locations where we have fiber optic internet service. Usually (from Zayo, Verizon, etc…
RE: Sophos UTM Internal Routing
Hi all,
I think this internal routing question goes hand in hand with my problem.
At one of our new locations where we installed a new AT&T fiber optic internet circuit we received different routing and IP information than for our other locations…
Auto renew WAN dhcp connected to cable modem on Error
I have my cable modem in bridge mode passing the public IP(s) through to the UTM to avoid double NAT. The issue is that I do not have a fixed public IP and the ISP forces a new IP every 24 hours. So I wake up in the morning and the WAN say UP - ERROR…
Workaround for dealing with inconsistent upload speeds
We have 3 locations - one hosts the UTM9 and two have RED50 devices linking our sites together for voice and data. All sites have download/upload speeds of 100/20 mbps. Because everything routes through the UTM, however, the reality is that our two RED…
Is there a solution to connect the WAN to a WLAN?
The case is this:
A customer has just WLAN in his homeoffice and would like to connect the RED-box with WLAN to his Router, which is located at another room.
Is that somehow possible? It's clear that he should have a stable WIFI-connection.
It's…
UTM to UTM link aggregation?
Hi!
Just a quick question: When connecting two UTM using a RED tunnel, is it possible to aggregate/bond WAN links on one of them in order to get a higher throughput?
I need to connect a branch office using two or three slow DSL lines to the main office…