Hi all, I am trying to migrate RAS SSL openvpn from an existing setup to sophos UTM 9 and I am struggeling with sophos certificate management. The existing openvpn setup works well and from a certificate point of view looks like the following: rootCA…

Hello @all, I am having problems accessing my internal network through SSL VPN with my Android devices (Sony Xperia Z5 and Z4 Tablet with both Android 6) and the OpenVPN App.. After connecting to the UTM I want to access an internal Website or a…

Is there any way to 'customize' the SSL vpn client config? It's nice the sophos bundles the install (S/W as well as cert/key/config), but haven't found a way to be able to add some directives... specifically, want to add additional "remote" lines. I see…

Hi all, I've recently replaced my TMG 2010 with the latest UTM 9 software appliance on a vm (ESXi). I must say, the WebAdmin is a treat, a wealth of options & features, with a bit of a learning curve as well, but loving it :) The LAN setup (private…

I migrated my software UTM (9.351-3) to new hardware a couple of days ago. I maintained the same version and imported the exported config from the old hardware. The old hardware had 5 network interfaces but one was unused and not assigned to any purpose…

I was connected via SSL VPN and decided to sniff my traffic to see which encryption protocol was being used. To my dismay I saw that it is SSLv2. This needs to change to at least TLS 1.1. How can this be done? I have UTM 9.401-11.

We have been using Sophos UTM 9.3 for well over a year now, a pair of SG210 in an active/passive standby. We have been using the SSL VPN for remote access on our user's machines. This has been working fine until recently for a few users, which are now…

How can I verify if all addresses are available? How can I reset this Virtual IP Pool? The usage graph also show that it reaches a 30 concurrent user ceiling.

While setting up the SSL VPN I was able to make a few configurations on my test remote client with multiple working VPN connections to the Sophos UTM all using the SSL VPN. But when I clean up and setup, how I would like, I found out that the user portal…

When I login to the UTM User Portal, go to the Remote Access tab, and click on the Install button to ".. install the SSL VPN configuration on (my) iOS™ device", I get the message " Error getting SSLVPN package, subtype config, user REF_AaaUseBthomson…

I tried setting up an SSL VPN tunnel for the first time. It seems to work as expected in "split tunnel" mode, where I can see devices on my internal network and also see websites on the Internet. What I want to do is route all network traffic through…

Hi all, We’re encountering a strange issue on one and only one of our users VPN remote access (SSL). When he logs in, the connection is ok, all routes are fine, but he can’t access any LAN resources. By working around, we spotted that he always get the…

Hello, We use for now SSL VPN. How we can configure time limit for every ssl vpn user to 90 minutes ? Thanks.

I have Sophos SSL VPN Client 2.1 installed (Win7 x64 machine) to connect to a client's network. When I check the SSL VPN network adapter it's reported to have only a speed of 10 MBit/s. Any way to change this to make the connection faster (because the…

Hello, I'm new in Sophos. I have couple of question: 1. If there is some way to configure that ssl vpn user that not working for 90 minutes (idle time) will be disconnect ? 2. There is some way to configure when ssl vpn user is connect, administrator…

I have a client site where I am having trouble accessing Domain resources. Version 9.352006 The VPN connection connects properly and stays connected without any problems, not seeing any telling errors in the logs at the client or…

The client log contains this error message repeatedly:connect to [AF_INET]x.x.x.x:443 failed, will try again in 5 seconds: The system tried to join a drive to a directory on a joined drive. Comcast is not helpful, anybody else overcome this symptom. Thanks…