Hi everyone, Similar to in TMG and Palo Alto, is it possible to match both source user group and source network together when building a rule? i.e. VPN Access users coming in on the VPN subnet can access services x,y,z. Thanks in advance. KJ

I added a second NIC to my UTM (192.168.3.*). The idea was to add an extra AP to isolate guest-clients from my local network(192.168.1.*). Everything seems to work fine. I get an IP from the DHCP service and I can access the internet from my guest LAN…

Hallo Community, Ich kenne mich leider mit dem Thema Sophos Firewall wenig aus. Beispieldarstellung: Ich habe 2 Interfaces (eth2 und eth4 an den vorderen Anschlüssen angeschlossen), welche in der Firewall auch angelegt sind (Interfaces & Routing…

Hello, We have license for 75 IP's LAN's and DMZ IP's go through Sophos FW. There is some way configure that all DMZ clients will get out with NAT ? I mean That sophos will stop count all IP's behind DMZ interface ?

I have published several RDP targets through my UTMs over the years, but this particular one seems to have me stumped. So, here is my layout. Internet -->Router (Subnet 1)-->UTM--(Subnet 2) Subnet 1 houses all of my General use items (WiFi TVs, Game…

Hi all, This is truly a weird one and I hope you can help me find a solution. We have 2 ASG525's running in active-passive HA. Last night I updated one to 9.353-4 but this problem was occurring on the previous version over the last week, I was hoping…

Hi, in won't allow (forbid) the Access to the Webinterface of the Router for the Guest-VLAN. But if I block all Traffic on Port 80, no is able to surf in the Internet. What else should I do? For good Ideas very thankful.

Hi, Just a “simple” Question, but I only use my Sophos SG 105 at Home, and so I’m no Specialist. I’ve two Networks (192.168.131.0 and 192.168.179.0) on two different Network-Cards (eth1 and eth2). The Access to the WAN on eth0 works for both Networks…

hi all, i have a few problems with the configuration of a vlan beetween sophos utm home and the tplink switch. my sophos has two ethernet interface, one is for ppoe and the other for the local network and the vlan, i set the vlan id at 100 and do…

I've been experiencing Open DNS Resolver attacks and would like to ensure my UTM isn't acting as an open resolver. I've tested through following means dig +short test.openresolver.com TXT MYIP Running this from outside the network returns ;; connection…

Hi, I’m using this product UTM/Astro software at my network entry point (since 2014) to protect my network, and I have an ongoing problems of disconnections in our web-access. I have this problem for a long time and despite version updates, hardware…

Hello everybody, my problem is, that i can´t connect to the internet via eth0 (wan interface). the dhcp and dns server on the utm is also activ and i get an dhcp adress from the utm, but i can´t connect to the internet. anyone who has the same problem…

I posted this to the Astaro forum, and it has been a work in progress, but I am still having this issue. Only 2 firewall rules are active. Whenever I stream from the pc, the Xbox One game throws a network error and disconnects me from the internet gaming…

UTM 9.3 Software version Onboard NIC - WAN Dual NIC Card - Internal Networks. I have just set up and activated the second internal network. I want to keep the two segmented and understood this was by default. However, when I tracert a device on network…

Posting this question again on the new forum.. Here is the link to the old: https://www.astaro.org/gateway-products/network-protection-firewall-nat-qos-ips/59993-additional-address-stops-responding.html Still battling this problem. Wondering if it is…

Hi, If I am using 192.168.0.0/24 and I have two neighbors 192.168.61.0/24 and 192.168.62.0/24 are there a LOT of places in the UTM 9.3 product I have to create this network and broadcast and link them to the firewall or web filter rules? Thanks…