When i try to connect to external network using sophos connect, my wireless gets disconnected and sophos connect fails to connect. When I use a wired connection no disconnection issues at all everything works fine.

Hello, I have the following problem: At our branch office, which is connected via IPSec, the users authenticate themselves via Radius in order to use the Wifi. I had already been able to test the Radius-Authentication successfully. Now a new access…

Hello, community I am new to the Sohos device and trying to help a friend recover his device. He had a power outage/surge and after that, the device has been having issues. (He was on a UPS/surge suppressor). Note: The device has a manufacture date…

Hello, I have created an account on Sophos Central in order to manage some APX 320 X and I can't connect these APs to Sophos Central. BUT , I already have Wireless Protection on my UTM 9 (firmware 9.713-19) enabled with nearly 60 APs configured. …

Hello, I am using the following: - SG125 with latest firmware 9.713-19 - APX320 (Wireless Access point) I use the Eth2 on SG125 that is connected to a device that is supplying a DCHP Server. It is required for a new project. The APX320 is…

Hi, We have a serious issue with a new AP we just received. The AP in question is the APX530. It's hooked up to a port on our Cisco switch which is a VLAN Trunk-type port, able to connect to all of our VLANs (more on this later), with the standard VLAN…

Hi all, I am new to this forum and have basic network knowledge. Therefore I am learning / configuring my home lab with an Sophos SG 115 including an AP15c. Everything is going well but I am not able to get the AP working. The problem is that I cant…

I have Sophos UTM with an Internet Speed of 200mbps bridged mode by ISP. But my wireless AP15 doesn't have the same speed. I only get 10mbps max.

I would like to segment my network into multiple LANs and VLANs. Right now, I have one happy LAN network, all shared with all devices. Small unmanaged switches in each room, converging to a large 24 port unmanaged switch in the office: Primary real…

I just replaced our old Apple "AirPorts" with Sophos AP 100C access points. When I enabled Wireless Protection I did the following: Enabled Wireless Protection with "Internal" as the allowed interface. Created a matching wireless network, Bridged…

I posted a similar question in the Wireless forum over a week ago, but got no replies, so I am trying in the general area. I am replacing my current access points with Sophos AP 100C models, to be run from the current UTM 9.7 software. The AP 100C is…

Sorry for the frivolous question, but ... I am replacing my current access points with Sophos AP 100C models, to be run from the current UTM 9.7 software. The AP 100C is designed to be hung upside-down from the ceiling, with the Sophos logo facing down…

Hi Guys i have a Sophos UTM 9 SG310 within the network i have 7 Reds connected and each Red has TPLink access point, I can ping and reach these access points via cmd and web browser. but the hardware controller which is a TPLink OC 200 cannot see…

Hallo zusammen Ich habe seit ca. 6 Jahren meine Sophos UTM SG115 in Betrieb. Aktuell mit der Version 9.710-1. Seit einem Systemabsturz und Neuinstallation kann ich den Reiter "Hotspots" im User Portal nicht mehr öffnen. Er ist ersichtlich, aber wenn…

We're seeing all APX320 AccessPoints managed by UTM becoming inactive after upgrading to 9.709-3. Existing AP55/C AccessPoint still fine. Anyone else with same problem? Workaround? Upgraded from 9.707-5 on SG310 (active-passive HA).

I configured a Wireless -> hotspot and it works fine but only if the ip address is in the same subnet of the UTM. If the hosted is routed I'm getting this error: The UTM ip is 172.16.0.0.16 If the client ip is 172.16.0.0.X, the hotspot login page…

I have an open ticket on this issue however; I am not receiving a response. I recently transition our wireless environment to support VLANs. We a had 2 networks that were set to bridge to the AP LAN (VLAN 2). I disabled those networks on our access points…

Morning all. decided to install Sophos UTM as my firewall (from a custom Linux box) and have a question about the wifi management... Can Sophos UTM manage non Sophos Wifi APs? or should i just create a VLAN, and associate that VLAN with the wifi network…

Guten Tag, ich habe eine "alte" SG210 Hardware Appliance und würde diese gerne Privat als Firewall und WLAN Lösung verwenden. Laut meiner Recherche kann ich die Basic Funktionen ja mit der Free Home Lizenz (bis zu 50 IPs) verwenden und diese auch…

Sophos UTM Home 9.705-3 AP15 single AP - no mesh Single SSID enabled I have been running UTM home for six years (2015) and the AP55 for five years (x-mas 2016). Last night, like happens a few times a month, my AP55 stopped allowing client association…

Hi! It's about an XG UTM with integrated WIFI and what already struck me as strange during the installation are the limitations of the bridge in terms of LAN and WIFI. Apparently you can only "bridge" WIFI with the LAN zone. Now the following questions…

Setup : Hardware: SG135 Software: UTM v9.705-3 APs: 2x AP55s Non-Standard Config: AP Country set to US (not to my actual location), for hardware compatibility reasons Problem: For at least the last year, wireless devices on my network have been intermittently…

Hi Everyone, The organization want to implement QR code for visitors accessing the Guest Wifi. The details of the QR code need to contain simple details of the Guest Wifi SSID simlar to image 1, in this way, device automatically gives an option…

Does UTM supports sending of voucher code thru SMS for users connecting in Guest WiFi, if so may I request for guidelines please. Thank you in advance and regards.

Hallo, out Wifi is currently very instable and the wifi is not available for a few moments. After the few moments the wifi is again available.We have 2 Network Device ( Wifi SSIDs namely 'intern' -> wlan1 and 'gäste' -> wlan0 Hardware: Sophos UTM…