Hi, we have 2 SG650 and both machines are connected via port eth0 [MGMT1] to administrate these. At the moment our active-passive cluster ha interface is on etc2 [A1]. Does something speak against it to switch the HA interface onto eth1 [MGMT2]…

We are facing issue whenever we perform firmware update, while running Up2Date patches getting installed successfully and post reboot we lost access to devices. In the above case 1. We can access device by using console/ HA interface i.e. ETH0 only…

Moin, Ich habe 2 WANs an einer UTM9 angeschlossen: 1x Telekom mit statischer IP, 1x Telekom mit dynamischer IP. Bisher war mein Netz über eine DynDNS Domain erreichbar. Mit statischer IP könnte ich zwar auf den Service verzichten, aber ich dachte…

Hi, We have a doubt ... Why the UTM HA does not swaying when the CPU Usage in the main UTM is high ? I show this in an image:

Hello, Does the command line "cc" or "/usr/locl/bin/confd-client.plx" have an option that allow to show the ha virtual mac? I really appreciate any help you can provide

Hello, I'm configuring 2 x UTM 430 devices in HA as an Active-Active, the HA is configured to monitor a 2 port LAG (LACP) to our Core switch. Our Core switch is in a bonded configuration VSS (ie, there are two disparate devices that are managed and…

Hello, I have a recurring issue that I have noticed at on Webserver Protection. Webserver configurations keep disappearing from web gui for real webserver and virtual webserver. I have 2 nodes in a master slave failover. The first time I noticed the…

I have 2 SG430s in HA, and heartbeats working fine. My next step is to allow seamless failover. Currently there is an internal facing, and external facing interface on the master UTM. When a failover occurs, (ie. firmware update) and the roles switch…

Hello, We're having some troubles with our SG230 cluster. We have 2 SG230 in 2 différent datacenter. with a HA actf/passif configuration. Everything was OK durint near 300 days. But last week we have had an incident in SLAVE datacenter (electrical…

The documentation on configuring HA only discussing configuring with hardware appliances. Is it possible to do HA using UTM9 software installs? If so, do the hardware platforms have to be identical?

Hello Community, as i have just received this question the 5th time already in two days i think i should inform you all about a message that is now turning up in the HA Logs. repctl[xxxxx]: [i] recheck(986): got ALRM / got HUP: replication recheck…

I have a Hyper-V VM running UTM 9.407-3 and it all works fine. When I try and enable HA mode between it and another UTM (blank config other than IP address, hardware and NIC config exactly the same) both UTMs become unresponsive in the GUI, and appear…

We are going to set up redundancy with two ISP, and use DNS for failover. Currently we have sohpos in VMware. We want to had another sophos for redundacy (HA), a hardware device, and use Link balancing between the two ISPs. . Problem: How would you connect…

Hallo liebe Community, ich bastele aus Interesse seit längerem Privat mit der Sophos UTM. Ich komme leider bei meinem aktuellen "Ziel" nicht weiter. Ich möchte zwei (virtuelle) Software Appliances als aktiv-passiv Cluster agieren lassen. Ich habe…

Hi All Hoping you could help me with some input here .. We have 2x SG230 UTM's setup in an Active / Passive HA cluster. I receive the following notification email once every 3 months per say - which indicates that node ID 1 (master) is offline and…

I have two ASG220 firewalls in HA Mode and I have a question when using Link Aggregation. Seeing one Firewall is active and other is standby. Do I also make 2 Link Aggregation groups on a Cisco Switch? One with the ports of each firewall??

Hello folks I encountered a strange situation which I cannot resolve using backup/restore and/or clean re-install. The Setup I have a 2 node virtualized setup like in the attached simplified image. I'm using the home edition of Sophos UTM 9.405…

Hi, I would like to know if it is possible to setup a HA with heartbeat link going through switches (LAG3 port 7&8). There are two datacenter, each one has 2 switches. Thanks for your help

We've been running pre-9.4xx releases on SG450 smoothly since initial deployment. However, after upgrading to 9.402-7 in Jun, unexpected httpproxy segfault comes: /var/log/kernel/2016/06/kernel-2016-06-15.log.gz:2016:06:15-17:10:43 sophos450-2 kernel…

This morning we had an HA failover where the slave became master. What I noticed after the failover is that logging (graphs) were not available in the period before the failover. This evening I let the previous master become master again and now I can…

Hi I have two nodes in an active/active cluster and want to be able to monitor the uplink interface to the internet on the slave node. When I log into the UTM, I get the Master unit and status of the interfaces on the dashboard, but I dont see anything…

Hi, We are using internet link from two different ISPs to have redundancy. Both links are terminated in UTM through a single cable running from each ISP provided device. Now we are adding another UTM for HA (A/P) but as only single cable is running…

Hi all I have a slight issue. We use Hyper-v as our Hyper-visor. I have configured 1 UTM which is live and is working fine. I have also configured another UTM to allow me to configure HA across two separate hosts. However the issue is when I enable…

Hello, We're having some troubles with our SG230 cluster. We have read this post https://www.sophos.com/en-us/support/knowledgebase/116131.aspx , so we were enough confident about the service availability during the updates. I'll go to explain the facts…