I'm upgrading my firewall and trying to figure out a simple way to switch my regular LAN from port1 to portF1 after importing the backup. I want to upgrade from the regular 1-gig connection to a faster 10-gig SFP connection. The tricky part is that there…
Hallo
ich habe ein Problem beim registrieren eines AP55c. Und zwar endet die Registrierung mit timeout. Wr bekommt von der Fritzbox auch eine IP zugewiesen. Die Diagnose meldet den AP als erkannt und das die Firmware auf 2.3.4-5 aktualisiert wurde…
Hey everyone,
I'm just wondering what weight is meant to represent when it comes to a backup gateway? Is it a percentage thing? Meaning if the primary gateway goes down, the backup will handle 20% of traffic?
Hello Folks,
a customer installed the ssd upgrade and after the reboot all ssl site-2-site tunnels don't work. ssl remote access works, ipsec tunnels are working.
here are some lines from the sslvpn.log:
we created a new connection, same issue…
hi Community.
we have a lte router with a static IPv6 IP-Address on the WAN-Side.
I turned on the DHCP for IPv6 as you can see below:
and as you see, the xgs gets an ipv6 address:
The Sophos Cluster has v20 installed and I can see the cluster…
I try to setup interactive HA on XGS 126 SFOS v20
I used to setup devices this way, now I must use the same IP range for HA and management?
The HA Link should be /30 network with only the HA IP - why must the management IP be in the HA network?
…
Hello!
Sophos SG310 V2
ISP: Cable: 940/50
I was running V20 GA for a couple of weeks, but I was seeing alot of glitch with online gaming and sometiems website would take a little longer to load. I saw also in the FW alot of Could not associate…
Hi,
Currently we are using Firewall XG310 and SFOS v20 . My question is :
1. How to bind vpn user mac-address without asking their mac-address manually? Could sophos FW detect it automatically ?
2. Could we set vpn user state duration ? Example…
Hello Community Members,
I want to enable DoS & spoof protection in my Sophos XGS2100. But, To enable it for all the hosts there will be a lot of trusted MAC addresses so adding them manually is a time-consuming process. So I came across this article…
I am using Sophos Xg 125w V20 and i have configured two Wan link Manager. Wan link manager1 as my ISP and Wan link manager2 for Vlans and i want all my normal browsing to go through wan link manager1 instead of each of my computer on my network to select…
1. Is there any option to disable Firmware Menu ---> Factory Reset option ?
2. Is there any option to disable COM port ?
We're managing through cloud central. We Also want to disable these two option as its deployed in branch office.
Today we want to replace our old UTM with an XGS 3100 cluster. In advance, we had created rules manually. But we were only able to test it today.
We have a LAN port 1 (192.168.2.0/24) and a 2nd LAN on port 7 (192.168.201.0/24) When I access 192.168…
This is the first time I've observed anything like this with the 3+ years I've been a Sophos XG home user. I upgraded to the latest build 222 about 15 days ago, so my run time has been about 15 days. Over the past several days I've noticed some weird…
Hi all,
I am using sophos XGS87 firewall with latest firmware version (SFOS 20.0.0 GA-Build222). I am facing issue with load balancing. Load balancing was working fine till yesterday. But today it is not working all the traffic is passing through…
Hello, I am experiencing an issue with the Sophos XGS firewall on the latest firmware.
The issue is with the Email application; specifically, incoming mail from the MailGun service is marked as b ounce+7bbc1d.e9c62-admin=acme.com .
It happens that…
Is it possible to route "streaming media" over a dedicated WAN-connection using SD-WAN routes in SFOSv20?
If not possible to route all streaming media, then is it possible to be more specific like youtube, tiktok maybe based on application rule?
Hello
same issue
SSL VPN config file naming
We got this since the firmware upgrade to XGS2100 (SFOS 20.0.0 GA-Build222), from SFOS 19.5.3 MR-3-Build652
The file has some other problems too, it now adds the CA two times, and at the beginning…
Hi.
I am having what seems a very basic issue getting my WAN connection connected to Sophos Home Firewall version 20, I'm hoping someone can help?
I've found various posts regarding this over the years but am still unclear exactly why it's still an…
Hello guys!
I have a home server running a few services on port 80 and 2-3 other ports
I also have dyndns (3 hostnames) and have been using waf to connect to those 3 services without the need to enter a port in the url
(There are also a couple of…
Hello,
I'm trying to import a .tar file exported from a UTM with the current firmware version 9.718005 into an XGS 136, following this guide. However, I keep encountering the familiar error message "The file that you are trying to import is not a supported…
Hi, I have gone through a fair bit of posts and how-to online, so I decided to post the question here, after 5 days researching this.
----------------------
My setup:
Motherboard with 1 built-in 1000mb/s ethernet port, 2x PCI-e cards HP NIC 2 ports…
Hi,
I just bought a SG125 Rev.3 and trying to get it running. I followed the steps as recommend in the different threads and created a bootable device using
SW-19.5.3_MR-3-652.iso
and in the second try
SW-20.0.0_GA-222.iso
In both variants everything…
I'm trying to test the web filter with a content filter and am experiencing unexpected behavior.
I've created a blocked terms list with the following term:
and uploaded it to a content filter called blocked_terms. I've also set up a web filter policy…
I’m a newbie in Sophos XGS VM version 20.0.0 , I want to make traffic shaping for two user groups for the same application category (Streaming):
Group A: Traffic limit for 125 Kbyte
Group B : Traffic limit for 1250 Kbyte
Is it applicable in Sophos…