Firewall XGS2100 to SD RED 20 : Connected Branch - SD RED 20 On LAN zone (IP 10.1.100.0 /24) HQ Firewall Xgs 2100: VLAN30 on LAN Zone (IP 10.1.30.0 /24) I'm able to ping Firewall and also access it but no traffic to Server Vlan30. Please support…

https://docs.sophos.com/nsg/sophos-firewall/19.0/Help/en-us/webhelp/onlinehelp/AdministratorHelp/SystemServices/RED/index.html For XG's on SFOS 19.0.1 MR-1-Build365 + RED firmware 3.0.008 with "Use RED unified firmware" not enabled and "Firewall RED…

Hello, I have a RED 50 that provides a LAN with an IP Range from 10.4.0.1 to 10.4.7.254. But, in some cases, my LAN has been almost saturated, and doesn't accept more IP connections. I have a second RED 50 (not installed), and I would like to use it…

Hallo Zusammen, wir haben folgendes Problem mit unserem WLAN. Wer haben an zwei Standorten die über RED 20 Angebunden sind APX320 und die RED20 WIFI Module im Einsatz. Nach einem Neustart der FW (XGS 136) waren die RED20 WIFI Module APs nicht mehr…

Disclaimer : This information is provided as-is for the benefit of the Community. Please contact Sophos Professional Services if you require assistance with your specific environment. ______________________________________________________________________________________________________________________________________…

Hi, Im working in retail company and last 2 days ago we faced an issue wherein our client could not communicate with the server located in the same LAN. Once you put the RED50 connection will hang and sometimes very slow. But without the RED50 and putting…

Hi, I had an issue in this scenario: XGS with SFOS 19.0.1 MR-1-Build365 + 2 RED60, Server W2012R2. The REDs operation mode is set Standard/unified; REDs are in a RED Zone. Each RED as it's own DHCP range (set in Network|DHCP (to be able to add static…

Hi Sophos Community, I am in trouble trying to send the Internet traffic of the client or branch site to the server-site or head office. The RED tunnel between two XGs is working correctly between Lan-Server and Lan-Client. However, I need to move…

I can't make sense of this issue, any help / ideas would be much appreciated because i feel like I'm taking crazy pills <insert Mugatu> I have the following setup: XGS 2100 Site 1 (Latest Firmware) SG 115 Site 2 The sites are connected via…

Bonjour Apres mise a jour firmware un red20 ne peux pas connecte j ai essaye de supprime et ajoute a nouveaux mais le même problème merci de me communique le unclock code n serie R20003BYP6RFY6E jai d'autre site 1 site RED 20 et 9 site red 15…

Hi, I would like to report an issue that we are facing and its happening frequently now. In our store we have POS and Server connected via LAN. This POS it will send an updated sales transaction to the server. Our issue after sometimes POS or files…

When Sophos will match competition with their RED offering like: - QoS - Web filtering Sophos was first to market with this type of device but now competition is doing far more ‍♂️

Hello, everyone, I have a problem. Device in Head Office: XG 230 (SFOS 18.5.4 MR-4-Build418) Branch Office Device: XGS 116 (SFOS 19.0.0 GA-Build317) After I updated the firmware in head office, the RED interface between head office and branch office…

Hi, We just upgraded an XGS126w which went fine but also had a RED 15w connected We then updated the RED firmware to 3.0.008 Since the upgrade on Sunday the RED is dropping all the time as soon as there is any traffic on it. We were not using…

Hi all, our SD-RED 20 with 3G/4G expansion wont fall-back to LTE connection. In the XGS config page I even can´t see if there is a LTE connection or not. SIM card is without PIN and is working with a Huawei E3372 without any issues. Setup done via WAN…

Hi, I have an eye on our XG DHCP and while dumping DHCP Traffic I found that on 3 currently offline REDs that are configured as Split/Transparent, send out DHCP Requests all the time. They are offline for days. 15:18:55.503884 reds30, OUT: Out 00…

I'm coming asking for help with configuring multiple DHCP scopes (vLANs) behind a RED that we want to operate in Standard/Split mode. We have a 'branch office' and want to be able to take advantage of the local internet speeds for WWW resources rather…

Hey folks, I have 2 XG 310 in an active-active HA. When failover occurs (Primary goes down), the RED tunnel goes down and there is no failover for the RED tunnel. I need to disable and re-enable the RED tunnel... Is it the correct behavior in…

I have a Sophos RED configured with a managed switch behind it. I had gotten this working as I wanted with "Standard/Unified" and a single tagged port on the LAN interface of the RED. I was able to access internet and resources behind firewall and could…

Hi, I've recently setup a HA active/passive pair of virtual XG firewalls running in VMware, with a branch office setup with a RED tunnel to the HA pair. Every time we trigger failover between the HA firewalls (ie rebooting or when I upgraded the firmware…

I have two sites that use RED devices to link back to our central office; one site uses a RED 15, the other a RED 50. Both sites are configured to operate in "Standard/unified" mode. The RED 50 is set to Switchport mode "Switch". At both sites, I also…

Hi, I know the question was the same for RED15s, but maybe Sophos has added a PPPoE function for newer SD-REDs?

I have a problem with SD RED 20. In XG210 for RED interface after boot new SD RED, i have this: Couldn't update the firmware. Reset the RED to factory configuration. If the error persists, contact support.

Hi All. I'm using XG (ver 18) and currently have a few RED15's setup and working fine. Just had a new SD-RED60 and I cant get it to connect up, do you set it up in the same way as you would a RED15 or different as its as SD-RED 60 ? On the device…