Hi Sophos Community, I am in trouble trying to send the Internet traffic of the client or branch site to the server-site or head office. The RED tunnel between two XGs is working correctly between Lan-Server and Lan-Client. However, I need to move…

I can't make sense of this issue, any help / ideas would be much appreciated because i feel like I'm taking crazy pills <insert Mugatu> I have the following setup: XGS 2100 Site 1 (Latest Firmware) SG 115 Site 2 The sites are connected via…

Bonjour Apres mise a jour firmware un red20 ne peux pas connecte j ai essaye de supprime et ajoute a nouveaux mais le même problème merci de me communique le unclock code n serie R20003BYP6RFY6E jai d'autre site 1 site RED 20 et 9 site red 15…

When Sophos will match competition with their RED offering like: - QoS - Web filtering Sophos was first to market with this type of device but now competition is doing far more ‍♂️

Disclaimer : This information is provided as-is for the benefit of the Community. Please contact Sophos Professional Services if you require assistance with your specific environment. Table of Content Overview: Scenario: What are the options…

Hello, everyone, I have a problem. Device in Head Office: XG 230 (SFOS 18.5.4 MR-4-Build418) Branch Office Device: XGS 116 (SFOS 19.0.0 GA-Build317) After I updated the firmware in head office, the RED interface between head office and branch office…

Hi all, our SD-RED 20 with 3G/4G expansion wont fall-back to LTE connection. In the XGS config page I even can´t see if there is a LTE connection or not. SIM card is without PIN and is working with a Huawei E3372 without any issues. Setup done via WAN…

Hi, We just upgraded an XGS126w which went fine but also had a RED 15w connected We then updated the RED firmware to 3.0.008 Since the upgrade on Sunday the RED is dropping all the time as soon as there is any traffic on it. We were not using…

Hi, I've recently setup a HA active/passive pair of virtual XG firewalls running in VMware, with a branch office setup with a RED tunnel to the HA pair. Every time we trigger failover between the HA firewalls (ie rebooting or when I upgraded the firmware…

Hi, I know the question was the same for RED15s, but maybe Sophos has added a PPPoE function for newer SD-REDs?

I have a problem with SD RED 20. In XG210 for RED interface after boot new SD RED, i have this: Couldn't update the firmware. Reset the RED to factory configuration. If the error persists, contact support.

Hi All. I'm using XG (ver 18) and currently have a few RED15's setup and working fine. Just had a new SD-RED60 and I cant get it to connect up, do you set it up in the same way as you would a RED15 or different as its as SD-RED 60 ? On the device…

Hi, I can't remove the RED device my sophos XG device. On System services, RED menu; when i want to turn on red status i get error like below I wanted to delete and re-add the red device on the device.

Hi, I have an email alert saying that my RED was down. Its a RED 20 connected to my XG 125w Firewall running the latest v19 firmware. I thought it would just show as down when logged into my firewall and viewing the RED interfaces but its actually…

Why VPN and RED dont work when date is not current in both server and client?

Hi, I tested Sophos XG Home and also XG trial (client and server both software VMs), but with both RED tunnel dont work. No L2, no VLANS, only L3. I have also hardware XG86. When I use XG86 as server and XG Home (software) as client, all works …

Updated 2 routers that have RED 15 devices attached. Updated to the latest firmware. Both Red Devices are now on 1 minute connect/disconnect loops. 4 hours on phone support with Sophos to get no answers. Anyone else experiencing this? I now have…

How can I enable a WiFi module in a RED20 that has been configured in XG without WiFi? This has been asked here but I do not find a solution there. https://community.sophos.com/sophos-xg-firewall/f/discussions/124305/red-20-devices-initially-added…

Hi, Trying to get my RED to passthrough a local VLAN but doesn't seem to be working. Having the RED in switchport mode SWITCH obviously doesn't pass it through, however local network works perfectly. However when i change the RED to switchport mode…

I'm trying to configure a remote office (5-10 users) using either an SD-RED60 or Sophos SD-WAN using a second XG Firewall. I don't want to have to make a separate subnet for the few users (I'd have to change a bunch of other routing if I did so), so I…

Hello good Morning a question friends is the sophos XGS 116w compatible with the XG230 firewall? is it the same as a RED15w in terms of configuration? as I have several of these added to my XG230 it is added just like the RED one, I need it to create…

We have the following scenario: Sophos XG135 (SFOS 18.5.2 MR-2-Build380) Port 1 gateway to fibre internet Port 2 Gateway to VDSL Port 3 Gateway to LTE Port 4 LAN Clients Port 5 LAN Server Port 6 DMZ The XG connects multible IPSEC tunnels via Port…

Has anyone done one of these before successfully? I've had no problem with any of the Standard mode configurations, however this Transparent/Split one has given me a headache. I've even got a call open with Sophos and have had a lengthy call today were…

We have a remote employee utilizing wireless internet provided by their landlord. We would like to procure a wireless to ethernet bridge for the wired DHCP handoff to a RED 20. I am seeing some Cisco WET devices that could fit the bill. Has anyone had…

Hi everyone, we created a BO and connected this site with the HO over a RED60 without VLAN tagging. So far so good :-). Now we would like to enroll some AP's in the BO with a setup similar to the HO. In the HO, we make use of Unifi HD nano AP's with…