Hello, I created a VLAN for my WAN interface. I see the IP in my FritzBox but the Gateway in the Sophos XG Home is offline. The ping check under "diagnostic" failed, too. Fritzbox Network Interfaces Gateway

Hi! I have Sophos XG106 rev.1 with home license activated SFVH (SFOS 19.5.1 MR-1-Build278) . Every few days the gateway/wan port goes down, attached log bellow: -- cd /log tail -f dgd.log NOTICE Mar 17 09:45:33Z [5495]: Executing : <gateway…

Hi there, I have one question related on the DSL Module , we configured everything like it should be - the connection works fine. But we have a small issue, that it shows the interface under Control Panel / System always as down. I remember something…

I need to support to configure a network. I have one ISP connection. ISP Provide us one primary IP, One secondary IP, One Data link IP and one Public IP. Now I need to configure our firewall before the router. p2p primary ip: 10.255.191.149/30 p2p…

In preparation for a Network upgrade (which we are also re-subnetting the entire network) I'd like to connect our new core to our XG 550 on a newly installed 10G port on a separate subnet. The existing is on a 1G 10.10.x.x /24 the new will be on 10.16…

WAN interface keeps going down every one /two Hours or so days. It started earlier this week and I can't find a reason why it happens. Once I reboot the router, it comes back up.

Hi all! Quick question regarding XGS 126: MTU is a property of the physical interface. If I want to reduce the MTU for a VLAN I have to do it on the physical interface. By adjusting MTU value I seem to lose the VLAN interface and the associated dependencies…

Hi, I would like to remove an interface of a LAG (HA AP Setup with 2 Nodes, XG310 (SFOS 19.5.0 ). I removed port8, clicked save, then the XG rebooted and the 2nd node became active. There the interface was still present. A renewed reboot back to node…

Hey, I am stuck with removing an interface from br0 on XG115w (SFOS 19.5.0 GA-Build197) I was trying to remove one interface from br0 and apply changes. Now I can not edit any details of the br0, the UI stuck in an infinite load cycle when I open…

Hi, It is possible to connect XGS3300/4300 to core switch with RJ45 SFP+ ASF-10G-T transcievers to get 10Gb/s speed over cooper? Any other transciever option, on link listed below I can only find this option for XG, not for XGS models? Has anyone tried…

Hi Community, is there a way to trigger a poe power cycle on poe ports on xgs firewalls. This would be very helpful to reboot a poe device remotely. Thank you. Kind regards, Chris

LAN LAGG (NON LACP) Active/Back-up Stops working after 5mins. I have to unplug one of the links for it to start working again. Until i unplug one of the links, can't ping the XG, get online and the SOPHOS Wifi stops working..... Basically the LAN…

We are considering purchasing a Sophos XGS 116W for a new location. We want to use the firewall to protect 2 network segments and a wireless network segment. We do not want any of these three networks segments to be able to see the other segments…

We are currently being provided a block of 5 static IP's through our Comcast Fiber EDI connection with Comcast providing us (2) ranges of IP's. We get an L3 range and a Usable range. My understanding of this is to allow easier troubleshooting of the Comcast…

In our production environment we have replaced our old firewall with a Sophos XGS 116. We have replicated the rules we had in our old firewall and everything seems to be going well: our applications are accessible, we can manage our databases... in short…

Hi We have a fibre link from our ISP with a static IP and a secondary / extra range of public IPs. Public IP: 100.100.100.62 (numbers made up) with GW 100.100.100.61 - This is the primary IP we use. We also have a set of secondary public IPs on…

Dear Mate, I've two links one is a static IP address another is a PPPoE connection, both links are ACTIVE connections, whenever a static IP link is down, the PPPoE connection is not working properly, it's very slow but that pppoe link is 400mbps line…

Hello. I have 5 different PPPOE accounts from my ISP .. ISP gave me one fiber modem with Ethernet cable out of it ... I was able to start one PPPoE session without any trouble, but I don't know how to start several sessions on one port. Adding an…

Running SFOS 19.5.0 GA-Build197 How to enable SNMP via WAN port? I have enabled: System > Administration > Device Access > SNMP on WAN and LAN There is no response to SNMP queries from the WAN. However, it works fine in LAN. What else needs to…

Hi all, I need to know how to configure my sophos xg with modem , but this modem is in router mode not on bridge, because ISP didn't allow me to make the modem in bridge mode. I have fixed ip public and i never did this configuration ( FW XG <---…

We have a problem with migrating our configuration from 17.5 > 18.5 The IP which we used to login through the weblogin has changed from 192.168.85.4 to 192.168 .89.10 The topology looks like this [FW-ASA]-[FW-SPHS] | [USER] So there are three interfaces…

Hi, Please, we are on version 19.5 This doesn't make sense... 1,10,12,2,3....

Hello, I am using a Sophos XG firewall (Version 19.5) and I have 2 WAN interfaces on that (1 active, 1 backup in the WAN link manager). To have the backup line not unused, we use it for SSL VPN (which works without problems). The problem is, that the…

I've got a Sophos XGS116 at a colocation site where we host a bunch of servers for our clients. Currently on SFOS 18.5.2 MR-2-Build380 although I can update it before this changeover if needed for functionality for my request below. Otherwise, I was going…

I have implemented my sophos firewall in bridge mode. I have access to the internal devices, but I cannot access the Internet, what needs to be done to access the Internet? I was trying with a firewall rule but it didn't work.