Hello, I installed Sophos XG on the cloud. I can't access it from the web because it is port 2 WAN, and it should be the LAN, but I can't change it. Is there any way to change the zone from WAN to LAN? It's the home edition, so I'm not sure this is the…

Anyway to turn these off from showing in the logs? Thx

Sophos FW for Production has failed to open on Google Web Browser however the IP is reachable. Version: XGS4500 (SFOS 20.0.0 GA-Build222) Mode: HA Any solution towards that. Thank you

I need to log in to our router via SSH because the web console lacks the ability to disable SIP ALG. But when I try to login it claims my password is wrong - even though I just used it 2 minutes ago to access the web console. SSH is enabled for the…

hi, we had an incident where when of our devices had an attempt of access but with failure due to wrong password trials. I an suspecting that this device was on an unknown network outside our organization due to work from home policy we have. Is there…

Hi, I've got a used XG 115w rev3 and installed the Sophos XG Home Software Version on it. The issue I encountered was that after a successful installation of the SW image, I cannot reach the appliance to complete the initial wizard. When patched…

Hi, I recently acquired a used XG135. When I got it, I plug an ethernet cable on Port1 and the light was on and told myself that all was ok then. So I decided to make a reset factory, and since then the Port1 never show up. No lights, no connection…

Hello! I've obtained a retired XG 210 rev2 for my homelab and have performed both factory reset and admin password reset via console. The admin password is successfully reset on the console side as I can login using admin/admin however the web portal…

Hey everyone, I'm pretty new to Sophos and networking in general, so this might be a dumb question, but I was recently given a SG 115 appliance to play around with and figured I would install Sophos Firewall v20 MR1 on it instead of UTM. So I figured…

Hi, I have the problem that the firewall is temporarily not operable via the web interface and is stuck. The status page doesn't show anything when it comes to performance either. tested across various browsers and systems, including sophos central…

Hello everyone, We are accessing a customer appliance via IPSEC-S2S VPN. Access is made to an IP that is NATed in the tunnel on the customer side and translated in the IPSec config on the customer side. Nothing special, has always worked. In addition…

My sophos Stopped Access to GUI & SSH after creating a NAT rule how can i delete this NAT rule ?

Hey everybody, i have a strange Problem. I have Firewall on Main Office and a Firewall in Azure (Both with Firmware SFOS 19.5.3) I have a working VPN and everything seems to be fine. But i cant access the Main Offices Web GUI or SSH CLI from…

I'm using the Home Firewall 20.0. I configured IPSec VPN to access devices in the home. I can access most devices, but not the Sophos firewall itself. Although the VPN shows up as a zone, it does not show up as an interface (a "tunnel" interface, with…

Hola comunidad, tengo el siguiente inconveniente. Resulta que para la empresa que trabajo compro un XG 125, lo instalo un proveedor y se quedo con la administración del mismo, que puedo hacer para poder tener la administración completa de este, no puedo…

I have two home deployments of Sophos Firewall v20, one at home and one at a family vacation home. I've set up VPN, routes, and rules between without issue. But the strangest issue that I can't seem to resolve is that with the vacation home the Admin…

Hallo, wir haben zwei Sophos durch einen SSL-VPN Tunnel verbunden. Ich möchte gern durch diesen Tunnel auf das User-Portal zugreifen. Die Pakete kommen auch dort an, aber laut trace gibt es einen Verstoß gegen die ACL: Violation; Local_ACL Lt…

Hello Stalwarts, I am trying to login on web GUI portal @admin user but it is getting failed, I have reset the password Using console cable but the error is same when i try to access SSH it's working fine. How to find what is is the issue ? Thanks…

in recent scanning, we received "SSH Terrapin Prefix Truncation Weakness (CVE-2023-48795)" vulnerability on port 22. just use this command in nmap "nmap -sV -p 22 --script ssh2-enum-algos 192.168.xxx.xxx" if it shows "chacha20-poly1305@openssh.com…

Hello, we have got a notification from the xg that a login was attempted for the admin portal. The admin portal is inaccessible from the internet. Message: The administrative access from IP Address '84.19.xxx.xxx' is blocked for '5'…

Hi all, I've been receiving this alert for a while now, let's say at least 2 years!!!, at varying frequencies. sometimes several times a day, sometimes a few times a month. when I check the hosts, I don't find anything in particular, sometimes it even…

Dears, I have a two firewalls, main firewall and a secondary firewall, and there is a connection between them through a VPN, in the past, access to the remte firewall from the main headquarters was through the VPN port, but now, when I want to enable…

Good Day All. I built my Sophos Firewall, downloaded and registered SFOS. I use this firewall in my home network and I made a recent change to Static IPs. Once I set a static on the WAN interface, 2 things happened. I could not longer access the Web Admin…

Hi, I have found the below log in one of my firewall. Want to block them The administrative access from IP Address '59.173.19.11' is blocked for '60' minutes after '5' unsuccessful login attempts . Thank You.

Hello, Have an XGS 116 with configured VLAN's on Port1. Trying to get to https://x.x.x.x:4444 or https://x.x.x.x times out when on the VLAN. I can ping all the VLAN devices and the default network devices successfully form the VLAN and vice versa. Device…