Hi,
Good day... We have 3 Gateway in our Sophos XG Firewall, as shown in the attach picture. Now we are planning to cancel the current link which is Port2. Now we are planning to slowly move the existing RED 50 connection to other Gateway interface…
Cheers
I have a Sophos xg ver 3 unit with v18. The Dual WAN gets setup and Shows connected under network. Both WANS are given DHCP addressess. The XG shows both green for 60 seconds then it chooses one green and one red. The one marked red will not…
Hi all
We have two internet lines and weights set as below
The customer wants 80% of internet traffic to go out on the VDSL and the rest to go out on the Leaseline. Have I set the weights correctly?
The next question is the default SNAT rule…
Hello...We have an XG firewall configured with (2) WAN interfaces. The primary is a cable connection from COX. We have a second one configured as a Backup in the WAN link manager that is pointing to a CradlePoint router with a Cellular SIM installed.…
Hello,
I'm migrating a network from an old Sonicwall to a new Sophox XG125w.
I added the device to my Sophos account and activated the licenses.
When I ran the setup wizard it was able to download the latest SFOS 18.0.4 MR-4 firmware and install…
Hi, i have XG V18 Mr4 with 2xISP for Internet and one MPLS Data link to get connected with my head office.
Q1: I want to do load balancing and failover in 2xISP. in V17, this was simple by using firewall rule. i can select primay gateway and backup…
I'm looking to add a backup cellular ISP service to my home network such that in the event my primary ISP is down, Sophos XG will use the backup cellular ISP. However, I really only want to use the backup cellular ISP to maintain internet connectivity…
Good Evening,
I have two public ip addresses from two different ISP's .How do I configure an additional WAN interface to accommodate the two ip addresses of different blocks from the ISP'S.I also want to implement load balancing on the sophos appliance…
Good morning!
May I please ask for your advice on the steps needed to create a new 'Active-Backup' interface?
Right now, I have Port1 as the LAN port at 10.10.1.1 and most devices on my network use that IP as the primary gateway address.
What I…
Hi,
I have configured 2 ISPs. One is on Port 5 (Name is broadband and IP is 10.102.252.14). Second one is on Port 6 (Name is airtel and IP is 182.75.145.85). I have also configured WAN Link Manager where airtel Active and broadband Backup.
But when…
Hi all,
I have an issue with WAN failover and the 3CX phone systems we deploy, most of these systems are deployed so the network looks like the below:
Bridged Modem & 4G Modem ---> Sophos XG or Unifi USG ---> Rest of the network.
If the primary…
We already have one ISP connected to Firewall, now we have another ISP connection for redundancy and load balancing. but XG 135 shows only one WAN interface. from chat support they said its possible to convert and use other LAN port as WAN but they didn…
Hi, i ran into a weird problem. We have two DSL-Lines, so we wanted to use each DSL-Uplink for different local subnets. No failover or load balancing. Just active/active.
We have a local net 192.168.100.0/24 and another with 192.168.200.0/24.
Now…
Hi!
I am trying to check the connection status of an XG210 (SFOS 18.0.1 MR-1-Build396).
The firewall itself has multiple WANs configured. I am trying to check if WAN is reachable via API-Get Requests.
via (Powershell example):
https://$($ip…
I am having Trouble getting 2 Active WAN Ports on my XG115 v18 Firewall. I have configured Ports 2 and 3 for WAN and both are set to Active. When I look at WAN Link Manager it shows that Port 3 is never active. I have tried with both being same weight…
I have just one internet service provider. From this ISP I have 3 blocks of public IP addresses, which means 3 different gateway addresses.
On the XG firewall I ended up creating 3 WAN interfaces - one for each Public block of IPs where one IP from…
HI , where i can find this i've been looking for hours still can't find PRIMARY gateway and backup gateway in RULES side after i upgraded to v18
Much thanks for your support
Hey Community,
A redundant internet connection requires two or more WAN interfaces with different internet gateways. If the Active gateway goes down, traffic should fail over to the Backup gateway. When the Active gateway comes back online, traffic…
Hello,
I have been experiencing a strange issue since July 8th: one of my 2 internet connections, a FO one, keeps going down frequently, but when I go into the admin page and try to run some diagnostics, say, ping 8.8.8.8 on that interface, then it…
I have a dumb question on the interaction of firewall rule settings and WAN failover rules. My particular network has three WAN links: One fibre, one cable and one LTE. The fibre and cable are both set to active, while the LTE is set as a backup which…
Hi,
Our WAN Link Manager configuration was working fine until today. If I disconnect the main ISP network cable, the second ISP link takes over. Wan Link Manager shows the backup gateway as activated. Windows 10 is showing that I am connected to the…
So, we have a 4G SimpliFi system hooked up as a Backup WAN Link. We've tested this, works GREAT! However, we've identified that in the event of a WAN failover to our backup link, we want to only deliver Internet access to those services we've deemed critical…