Hello, i have sophos xg who have 2 rules, 1 rules is drop all connection and i place that in bottom, 1 rule allow to some sites like pic i attach, but, when I try to access some of these websites, some are still blocked, and some don't load properly…

So this is basic I'm setting up a firewall rule to allow specific VPN traffic Here's the specific service definition Attempting to setup a VPN, I get this... Here are some of the same drops from the full firewall log Why is this traffic…

I still have an old Cyberoam CR100ia (yes, I know it's end of life) and am wondering if anyone can help me with a firewall rule. I am using a virtual host for passing traffic to my mail server. I have a rule allowing any IP to my NAT destination/services…

Ok, so how specifically do I ' set the corresponding intrusion protection rule to "drop" in WebAdmin ' per the alert email below I received? There is no 'rule' identified in the alert. Am I supposed to infer that 58442 in the snort link is the rule…

Hello all, Networking certainly isn't my forte and I've only really been handling our UTM sporadically for 2 years, so please bear with me. I did not install the UTM nor was I the primary admin, but I want to make sure that we're decently secure. …

Hallo zusammen, ich habe ein kleines Problem bzw. einen Denkfehler wie ich verschiedene VLANs verbinde. Die Anforderung sieht vor, dass die Kommunikation über ein ungenutztes, selbstständiges V-LAN (bsp. VLAN2) laufen soll. Mitarbeiter aus bsp.…

We use the 8x8 Work Desktop application. The app employs WebRTC and I'm getting a few hundred thousand default drops for UDP packets going to 8x8 turn servers every 24 hours. The turn server IP addresses (all 8x8 IP addresses for that matter) are in the…

Hi, Is there any link with the rules description and rules ID for the Sophos Optix alerts, I've been looking in the official documentation but was not able to find anything related to the rules information. Also is there any documentation related…

I have tried the following scenario by building the DNAT rule and Firewall rule manually. And I have tried using the "assistant." Neither work. I would appreciate if someone could take a look at this scenario for me since the support portal is still down…

Hello All, This is a repost of an unsolved problem from the Sophos subreddit ( www.reddit.com/.../) , so if it looks familiar that's why. I'm running Sophos XG SFOS 18.0.4 MR-4 and running into issues with web filtering. In short, the category "IP…

Currently, the UI in the UTM allows blocking active content which includes ActiveX, Java, and Flash. Flash is now obsolete and considered risky to use at all. The manufacturer is now blocking it. I propose the UI be chanced to allow for the blocking…

I have two Sophos XG330 (SFOS 18.0.3 MR-3). A page is blocked, which loads some more data from external pages. Error: Uncaught ReferenceError: YUI is not defined Cross-source (cross-origin) request blocked: The same-source rule prohibits reading the…

HI , where i can find this i've been looking for hours still can't find PRIMARY gateway and backup gateway in RULES side after i upgraded to v18 Much thanks for your support

Good Day, when you have enabled blocking of unknown Websites and you are surfing on unusual websites such as personal websites of small companies or blogs you always have to submit thousands of Websites for categorisation because they are unknown…

Hello Sophos-Community, my problem is the following: I am trying to set the following permissions for our ssl vpn: access to 192.168.13.0 access to 192.168.13.11, but just a specific port. It shouldnt be a firewall deny or discard rule because…

I currently see a live connection running since early in the morning based on HTTP Resume Filetransfer. Investigating the destination IP address I found out it is web radio (http://94.130.253.194/). How can I block web radio? - I don't want to block…

Hi, I am new to sophos XG, I integrated successfuly my domain controller with the firewall. I added the groups and the users and I created a rule that enables only some users from my LAN to access WAN. The problem is when i test it in the policy test…

I am using sophos xg on vmware. and i want for Dmz to communicate with WAN. I created a rule that is correct but the trafic does not pass. the DMZ zone is on vmnet5 and the WAN network is bridged. here is my screenshots to my sonfiguration. Thanks for…

Hi there, New user here, could someone please explain these connections to me? I have default WAN to LAN IPS and the default firewall on for now (which allows any connections). I would hope that the IPS blocks malicious connections and keeps ports…

Hi all, I've hunted through the forum but I am unable to find precisely what I am experiencing. I think my issues is related to firewalling. I have a network with two gateways. One is a managed router controlling access to all of our remote sites…

Goal: Allow persons on the guest network to stream iTunes to Airport Express units connected to the main LAN network. XG firewall with 3 networks: Port1 LAN 192.168.7.1/255.255.255.0 Kids Wifi 172.16.40.1 /255.255.255.0 Guest Wifi 172.16.50…

Safe Search Enabled on the applience but the youtube videos got error " This video is restricted. Try signing in with a Google Apps account. " how can i resolve this isuue

Hello everybody, I need some help here. I recently migrated from pfSense to Sophos XG home and I really like it, but I have some trouble getting my routing configured. Basically I want to configure remote access to my media servers. What I did is…

Hi all, We're currently experiencing and issue where our XG230 is blocking a migration of public folders to Office 365 from on premise Exchange 2010. The migration works if we place a DNAT rule using port 443 that forwards to our exchange. The only…

Dear all, I am new to the Sophos Endpoint Control application. Currently I am in the need for a specific situation, maybe this will be easy to solve, maybe not possible at all. I have Windows 7 and Windows 10 (soon to come) clients. We have a VPN that…