Hello, good morning everyone ... I have a Unifi network ... consisting of a Gateway + 3 sw and 3 Access points a Cloud key controller, Now the IT administration has acquired a Sophos XG230 Firewall for perimeter security. There is some way to incorporate…
Hallo,
mit einer XG 310 sind 2 RED60 und 2 RED50 über Internet verbunden. Die zwei RED60 u. eine RED50 sind mit der XG310 im Bridged-Mode. Die letzten Wochen habe ich täglich das Problem, dass das Netz hinter den beiden RED60 und der RED50 nach einer…
I'm trying to understand the best way to configure the firewall so it can see what's going on and alert me but not get in the way and avoid any changes to my network?
I have a Ubiquiti USG as the gateway device that feeds an 8 port switch. I thought…
Hello,
I need to pass a public IP from my router XGS3100 to a virtual XG firewall for legal purposes, example Port 2 is the wan 1.1.1.2, port 1 would be connecting to the Virtual XG firewall and would like it to be 1.1.1.3.
Thanks!
Hello Sophos, I am pretty new to sophos and I have one particular situation. I have a notebook directly connected to one bridge previously created but i can't reach others hosts inside bridge.. devices connected to this bridge can not establish an local…
Anyone know of a way to get OSPF working on a bridged interface (Br0) that has routing enabled? What I am seeing is it attempting to send out the general ospf multicast traffic looking for neighbors but nothing responds. I have traced this back to something…
Hello everybody,
I would like to know if it's possible to add VLAN to a Bridge port.
For example:
Bridge port = Port1, Port4 and Port8
VLAN = 20 and 30
I would like to add those VLAN to the bridge. I receive IP from each VLAN but I cannot…
Hello all,
Is it possible to place the Sophos RED at a secondary location but then use the same IP range from the main location via dhcp? So do you have to create a bridge for this or what would be the best approach?
Thank You
Hi. So I had 2 ports bridged (Port 1, 3 and 4) to the LAN port (Sophos XG V 18.x)
I want to use Port 3 for DMZ as I need that now.....So I removed port 3 from the bridge. I still have access/ connectivity etc. via LAN so thats not an issue.
I have…
Hi All,
this is my first post and sorry for my poor english :-)
I have an XG Firewall that I configured so:
Port 1 bridged with Port3
On Port1 I connected my LAN on Port3 I connected a router (IP. 10.0.0.65)
IP on bridge are:
10.10.10.1 /…
Hi!
It's about an XG UTM with integrated WIFI and what already struck me as strange during the installation are the limitations of the bridge in terms of LAN and WIFI. Apparently you can only "bridge" WIFI with the LAN zone.
Now the following questions…
XG105w V17MR-15
Port 3 in our firewall is free - i.e no cable connected. We would like to remove it from the default bridge on our bridge0 interface but it looks like we can only remove the bottom two. The reason we want to remove port 3 from brdige…
I fully configured an XG135 (VLANs, DHCP interfaces, etc) and realized that I neglected to bridge 2 additional ports for the default LAN (port 1). Is there any way around losing my DHCP and VLAN configurations when this bridge gets created?
Hello everyone...
I've been looking for my problems resolution for more than a week but haven't found similar situation.
I'm a new user of XG 310 with 18.0.4 firmware. I want to replace Mikrotik router which is the main part of the network with the…
I apologize if this has been explained somewhere else and please feel free to direct me to the answer.
I have a XG appliance that we want to bridge 2 interfaces and create them as a bridged trunk for VLANs.
So on the XG we have int 1 and int 2 that…
In case I use the router, configure it in bridge mode and connect to a firewall that accepts IP on the WAN as DHCP, which if the router has updated the IP but the WAN pin is still the original IP address, not exactly how to configure it. To keep the WAN…
Complete Noob here trying to get started. To this point I've done the following:
My goal setup is as follows:
WAN->router->utm->internal network. utm is running in microsoft hyper-v .
Configured a bridged interface as follows:
2. Added the following…
Hi there,
I am a home user. I have a modem/router combo, behind this an asus router, which I need, due to tx/rx performance.
I had the idea to use my home sever as a (virtual) firewall, why I have virtualized a Sophos XG (latest) firewall in Hyper…
Ich habe da mal ein Problem welches ich derzeit noch nicht gelöst bekomme. Eventuell hab ich einen Hirnhänger.
Ausgangsituation:
Ethernet "Intern" (inkl. DC mit DHCP für Clients im "Internen" Netzwerk)
WLAN-AP's: VLAN20 (UTM als DHCP-Server) …
Hello,
we have set this up for a remote location:
So the same VLAN ID on both sides: behind XG and behind RED, same IP Subnet.
Bridge Members, same Zone:
This is already in production and working. the RED60 Users can work on internal ressources…
Hello all,
I want to segment out our VOIP connection for our provider. Can the UTM create an interface with max DL/UP speeds? Our provider says they have everything configured right, but since moving from DSL to fiber, it has been headache central for…
Hallo zusammen, ich würde gerne mein bestehendes Netzwerk monitoren und absichern. Dazu habe ich mir eine Astaro 110/120 gekauft, auf der Sophos UTM 9.5 läuft. Nun stellt sich mir die Frage, wie ich das Setup am besten und einfachsten realisiere. Folgende…