Hallo, ich habe hier ein seltsames Phänomen. In einer Windows Domain (192.168.2.0/24, Zone LAN) braucht ein Windows 11 Client für den User Logon zwischen 2-3 Sekunden. Nun habe ich ein VLAN3 (172.17.3.0/24) mit der ZONE VLAN3 erstellt, der DHCP Server…

Hallo, Ich habe ein Problem mit einer RED-SD 60 und meiner VLAN-Konfiguration. Die RED hängt am Standort mit zwei Uplinks am Switch. LAN1 untagged VLAN 1 -> Switch-Port untagged VLAN 1 LAN3 tagged VLAN x,xx,xxx -> Switch-Port tagged VLAN x, xx…

Hallo, ich für mein WLAN (UniFi AP) ein eigenes VLAN eingerichtet, damit es vom internen LAN Netzwerk getrennt ist. Jetzt habe ich nur das Problem, dass mein Drucker sich im LAN Netzwerk befindet und ich ihn nicht mehr über AirPrint finden kann. …

Hi all, i installed Sophos on hyper-v (vm) with 3 NIC: - NIC-A “LAN” (physical nic on server) - NIC-B “WAN” (physical nic on server) - NIC-C “LAN” (private virtual switch hyper-v) I’ve created Bridge with NIC-A and NIC-C, with "enable routing…

Good day Members, I trust you are well. We are trying to setup a guest Wi-Fi with Sophos and Unifi. We have it currently working but with the DHCP server on the DC, We would like to move the Guest Wi-Fi DHCP to the Sophos XG. Main issue is device are…

XG210, SFOS 19.5.2 MR-2-Build624 So, I have two VLANs, VLAN 70 - 192.168.70.0/28 and VLAN 100 - 10.0.0.0/24. DHCP server is on VLAN100, I want to relay DHCP requests from VLAN70 to VLAN100 for service. I have a relay set up like so: Name …

Hi I am using XG-115 as my firewall and already got number of rules. I also have a couple of VLANs. I followed the below guidance given by Sophos tech support team. The rule works well with individual hosts. but when I replace the individual host…

I have a small problem, I have a mikrotik router set up wlan10 (10.10.10.1/24) on port 2 everything works, I connect directly to the router, I have access to the network via vlan10, and when I connect sophos home (in bridge mode), I have an address assigned…

i have dns domain server 10.0.0.1 mask 255.0.0.0 gateway 10.0.0.2 & and ip range is 10.0.0.1 to 10.0.0.254 but now i want to give different ip range to different department like 10.0.1.1 to 10.0.1.254 to support department and 10.0.2.1 to 10.0.2.254 for…

Disclaimer : This information is provided as-is for the benefit of the Community. Please contact Sophos Professional Services if you require assistance with your specific environment. ______________________________________________________________________________________________________________________________________…

Disclaimer : This information is provided as-is for the benefit of the Community. Please contact Sophos Professional Services if you require assistance with your specific environment. Table of Contents Overview Import/Export Configurations…

Hi, Sample: configured sophos XG135 VLAN1 to go through port 1 of the firewall , how do i set it to use port 3 and 4 on switch for VLAN1. VLAN1 goes though port 1 on firewall then port 3 and 4 on the switch connected . Port 1 part is done, how…

Hello, I have the following scenario, I need to transport some VLANs that are on my core switch L3, behind the RED (Appliance), I have already tried to put the Firewall interface marked with the VLANs that I need, in Sophos I grouped the VLANs in a bridge…

I just cannot figure this out now. Been trying this for a day and desperately need your advice on this. I am trying to build a simple separated (isolated) VLAN from Ubiquiti Unifi AP Network to Internet route: Unifi AP -> Unifi Switch -> Sophos XG.…

I have a VLAN, currently on Port1. Now I connected my XGS-126 to my switch using glass fibre. However, under Network/VLAN I cannot edit the Port# Which selection of the configuration should be exported? Would it be sufficient to export just the VLAN…

Hello, I created a VLAN for my WAN interface. I see the IP in my FritzBox but the Gateway in the Sophos XG Home is offline. The ping check under "diagnostic" failed, too. Fritzbox Network Interfaces Gateway

Good day everyone, I have been asked to update our network so our data demands can be met. Currently, we run a conventional flat network and our Sophos XG is routing all the traffic. THru my research I think the best solution is to design the network…

I followed this helfull guide: Sophos Firewall: Interface / VLAN Migration via XML Import/Export I am facing a migration from SG (UTM) to XGS (SFOS) with hundrets of VLANs an DHCP-Server. Sophos Migration Support converted the config of the SG and…

Currently, I created Vlans for my each SSID of my Unifi APs. I have 4 APs, all connected to my TP-Link poe switch, which is Vlan aware also. The poe switch is plugged to my Cisco switch e.g. port 10 (Vlan aware). All other desktops (not in Vlans), NAS…

Hi all! Quick question regarding XGS 126: MTU is a property of the physical interface. If I want to reduce the MTU for a VLAN I have to do it on the physical interface. By adjusting MTU value I seem to lose the VLAN interface and the associated dependencies…

I have a problem where I am unable to ping google and it somehow seems as the firewall is missing a route back to my client. My client is inside a VLAN (172.16.87.99) and from the traffic below I can see that it correctly routes to the gateway address…

Hello, i have a problem with the internet connection on physical port WAN with additional vlan (zone LAN). I tried to change the physical port to an dummy ip and zone DMZ and create two vlans 1 (WAN) and 40 (LAN). My router recognizes the IP address…

Hi, We have just started using Sophos FW and having some difficulties creating Rules. We have two vLANs vLAN10 and vLAN20. We need to allow vLAN10 to have full access to the internet whereas vLAN20 should have a whitelist, i.e. access to few websites…

Hi, I'm new with this equipments, i'm trying to configure VLANS between two equipments (SOPHOS -» Switch) SOPHOS: - WAN - DHCP from ISP router - LAN PORT1 IP: 192.168.100.1/24 - ZONE LAN 1.10 - VLAN 10 - 192.168.10.1/24 - PORT 1 - ZONE…

How many maximum VLANs support in XGS3100 and XGS4500?