Hello, we have bought an XG 210 and XG125 (EnterpriseProtect license) to change the previous internet gw/firewall (kerio control). We have 2 sites (40km apart) and XG210 will be deployed in SiteA and XG125 in SiteB. All the site have 5 Vlans each (server…

Hi all, I'm a little bit confused with the VLAN configuration on XG. I'm running a XG310 with SFOS 16.05.8 MR-8. We have 4 VLANs: - VLAN 10: 192.168.10.0/24 - VLAN 20: 192.168.20.0/24 - VLAN 30: 192.168.30.0/24 - VLAN 50: 192.168.0.0/24…

Hello All, I hope u will be able to help me. I'm using bridge interface which gives me nice one subnet segregation. Everything works fine only if every interface Port1, Port3,... inside bridge have separate switches for each port. But this is…

Hello I just (partially) installed an XG105. Most things work correctly but I'm having trouble getting a policy routing rule to work. This is the situation/problem VLAN10 (10.10.0.0 / 255.255.0.0) VLAN40 (10.40.0.0 / 255.255.225.224) range determined…

Hello, I have problems with VLAN and Sophos XG. Internet and everything is working on Port 1 under LAN Zone. I created a VLAN interface on Port 1 with VLAN ID 3516. but it shows N/A under status. I'm running a domain controller and some other…

Hello, i'm experiencing an issue with my XG105w. I have multiple Vlans in my network created with the xg105w, and when i transfer a file from 1 server being in the Vlan 1 to another server being in another Vlan, the transfer speed is limited at 60MB…

Hello, I got a weird issue with my XG105w: I have set up several VLans as follows: Vlan1: 192.168.16.0/24 Vlan10: 192.168.10.0/24 Vlan20: 172.16.16.0/24 Vlan30: 10.16.16.0 / 24 Vlan40: 10.0.0.0/24 My local servers (domain controller active…

I have the following Network topology WAN -> eth1 Internal -> eth0 (default VLAN untagged) 10.10.10.0/24 Internal2 -> eth2 (VLAN 10 untagged) 10.10.20.0/24 On the switch, I simply have dedicated untagged ports for VLANs for the respective networks…

After more studying the configuration on my sonicwall that I am switching out with a XG 310, I have a question about BGP routing. Based on the information below do I need to do any configuration to BGP routing on the XG? 2 cisco routers are connected…

Dear All in order to build a mDNS/Bonjour gateway, I have configured a RaspberryPi with 4 VLAN interfaces: eth0.110 with 10.10.110.20 eth0.130 with 10.10.130.20 eth0.210 with 10.10.210.20 eth0.230 with 10.10.230.20 The VLANs are defined in XG while…

I currently have a UTM setup with three different interfaces (WAN, LAN, and DMZ). The LAN and DMZ interfaces have DHCP servers setup with different subnets. The UTM is connected to a trunked port on a managed switch, which is also connected to a wireless…

Not sure where this question would go other then Initial Setup. It's more of a design question but its the closest group I could find. Currently our main office has a Sophos XG310 and a Cisco 1921 used for a point to point connection with a branch…

Please see the attached network topology, I'm looking for opinions on the best configuration based on performance and security. I welcome any suggestions that the experts on the forum can provide to assist with this config. I would also welcome…

Hello! Hopefully I'm just missing something easy with this setup but here is what i'm trying to do: I am using Sophos XG as my primary gateway for several vlans. Since I haven't been able to get XG to act as a VPN client (Would be a very nice feature…

How can I get these to work. Port 1 is my LAN, Port 4 is my Wireless Making the zones, then making firewall rules for traffic to go both ways is not working. ------------------------------- Port 1 - VLAN 1 --------------------------------- Port…

Hello everyone, I'm a new user of Sophos XG v16 and I'm having a little bit of trouble when it comes to communication across VLANs. I actually think I'm 90% of the way there, but there's something not quite right about my configuration and I'm looking…

Hello, Hoping I can get some assistance with what I am missing on this UTM SG230 running 9.407-3. I have seen other questions on here, however could not find one with a...complete answer. As well, I know all configurations are different. So, even a push…

Hello folks, been going at this the whole day and cannot get the gateway to show GREEN Ive tried in vain with firewall rules to get BRE2 to show GREEN. As a test i manually added BRE so i know the UTM can see the gateway on the router "Miktorik" …

Hallo Forum, ich bin kurz vorm Verzweifeln, da ich mein gewünschtes Setup einfach nicht zum laufen bringe. Im Grunde handelt es sich darum, dass meine IP-Türsprechanlage (Mobotix T25) über meine FritzBox an meinem FritzFon per SIP anrufen soll, wenn…

Hi; I have 2 IP address on my WAN port. One of them is port 2 main IP address (exp.212.212.212.2) other one is WAN alias IP address (exp.212.212.212.3). Also I have 2 exchange server each external IP address and VLANS on LAN network. This Exchange…

So I'll start off by letting you know I'm currently running pfSense, with no issue. The configuration is set as expected. I'm finding some odd behavior though in trying to MATCH the configuration with the Sophos XG. I can validate that with the UTM9 platform…

Hey guys, First, thanks for the help so far. I'm digging through. I'm having some trouble getting my VLANs (created on LAN) to communicate. I've tried about 100 different variants of rules and nothing seems to work. I'd like two of the VLANs to…