Liebe Sophos Community, ich möchte aktuell die Konfiguration meiner Sophos XG SFVH (SFOS 19.0.1 MR-1-Build365) über Ansible automatisieren. Vor allem möchte ich automatisiert VLANs zur XG hinzufügen können. Da ich für die XG erst gar keine Ansible…

Hi, Sample: configured sophos XG135 VLAN1 to go through port 1 of the firewall , how do i set it to use port 3 and 4 on switch for VLAN1. VLAN1 goes though port 1 on firewall then port 3 and 4 on the switch connected . Port 1 part is done, how…

Hello, I have the following scenario, I need to transport some VLANs that are on my core switch L3, behind the RED (Appliance), I have already tried to put the Firewall interface marked with the VLANs that I need, in Sophos I grouped the VLANs in a bridge…

I just cannot figure this out now. Been trying this for a day and desperately need your advice on this. I am trying to build a simple separated (isolated) VLAN from Ubiquiti Unifi AP Network to Internet route: Unifi AP -> Unifi Switch -> Sophos XG.…

I have a VLAN, currently on Port1. Now I connected my XGS-126 to my switch using glass fibre. However, under Network/VLAN I cannot edit the Port# Which selection of the configuration should be exported? Would it be sufficient to export just the VLAN…

Hello, I created a VLAN for my WAN interface. I see the IP in my FritzBox but the Gateway in the Sophos XG Home is offline. The ping check under "diagnostic" failed, too. Fritzbox Network Interfaces Gateway

Good day everyone, I have been asked to update our network so our data demands can be met. Currently, we run a conventional flat network and our Sophos XG is routing all the traffic. THru my research I think the best solution is to design the network…

I followed this helfull guide: Sophos Firewall: Interface / VLAN Migration via XML Import/Export I am facing a migration from SG (UTM) to XGS (SFOS) with hundrets of VLANs an DHCP-Server. Sophos Migration Support converted the config of the SG and…

Currently, I created Vlans for my each SSID of my Unifi APs. I have 4 APs, all connected to my TP-Link poe switch, which is Vlan aware also. The poe switch is plugged to my Cisco switch e.g. port 10 (Vlan aware). All other desktops (not in Vlans), NAS…

Hi all! Quick question regarding XGS 126: MTU is a property of the physical interface. If I want to reduce the MTU for a VLAN I have to do it on the physical interface. By adjusting MTU value I seem to lose the VLAN interface and the associated dependencies…

Hello, I am going to rent an office space to an external company. I have to separate the network so that the tenant does not reach our internal resources. can i set up vlan to separate? if so, how is this done?

I have a problem where I am unable to ping google and it somehow seems as the firewall is missing a route back to my client. My client is inside a VLAN (172.16.87.99) and from the traffic below I can see that it correctly routes to the gateway address…

Hallo zusammen, ich habe das gleiche VLAN auf zwei verschiedenen Eth-Schnittstellen und die sollen miteinander reden können. Muss ich dann für jede Eth-Schnittstelle eine VLAN-Schnittstelle erstellen und diese dann gruppieren? Ist das korrekt oder…

Hello, i have a problem with the internet connection on physical port WAN with additional vlan (zone LAN). I tried to change the physical port to an dummy ip and zone DMZ and create two vlans 1 (WAN) and 40 (LAN). My router recognizes the IP address…

Hi, We have just started using Sophos FW and having some difficulties creating Rules. We have two vLANs vLAN10 and vLAN20. We need to allow vLAN10 to have full access to the internet whereas vLAN20 should have a whitelist, i.e. access to few websites…

Hi, I'm new with this equipments, i'm trying to configure VLANS between two equipments (SOPHOS -» Switch) SOPHOS: - WAN - DHCP from ISP router - LAN PORT1 IP: 192.168.100.1/24 - ZONE LAN 1.10 - VLAN 10 - 192.168.10.1/24 - PORT 1 - ZONE…

How many maximum VLANs support in XGS3100 and XGS4500?

Dear Sir, i have already configure VLAN but i am not able to connected vlan to lan can you please help us and resolve this issue asap

I have a SG135 with UTM Home and a Fritzbox 6591. My Network is a followed: ETH0: WAN with IP 172.10.0.2 (Fritzbox 172.10.0.1 / Additional IP 192.168.3.1 with DHCP on UTM for WLAN over Fritzbox) ETH1-7: internal Network with 192.168.4.1 and DHCP Pi…

Hi, I'm trying to get my Guest WiFi VLAN working on SFOS. This was previously working fine with UTM9 but since moving to SFOS has stopped working! Running the SFOS virtual appliance in ESXi v8, configured as follows; vSwitch0 contains port groups…

We have a separate VLAN set up and working for our Guest Wifi network. Clients (mostly cell phones) receive a DHCP IP in the correct range, are segregated from any other network communication, and can get to the internet fine. What we would now like to…

I have 2 Vlans on my network, 1 for voip and one for manageing devices such as swithces and accesspoints. until recently i was using a different router and that worked fine however sincce switching i am unable to access the vlans on th email network…

Hello all, Currently, we need to migrate our existing Firewall Watch Guard Router whose license will expire soon by the Sophos Firewall. So we ask for your help to set up a trunk between these two routers, indeed the idea is that the Sophos will play…

Hi All I would like to create a Lan trunk between the Sophos XG Firewall and the Cisco Router This is my topology Could you please help me

Hi all, User Kyle Sexson had this issue a while ago, too, but there’s no solution in his post - so… I have a set of VLANs running on a bridge interface. This works mostly well, but certain outgoing traffic will show up both on the bridge interface…