After a Reboot, we cannot query our XGS SFOS 20.0.1 with SNMP anymore due to errors with the snmpd service. Before the reboot it was fine. snmpd is running. saving the config again via Webadmin does not fix the issue, it restarts with the same errors…

Hi, We have configured the SDWAN profiles for the WAN links and we are observing the pocket loss and latency on the particular link, Is there any way to get the notifications on these profiles over mail or SNMP ?

hello, I noticed that when I execute the `snmpwalk` command on the OID `.1.3.6.1.2.1.31.1.1.1.18` (ifAlias), the result comes back empty. When I execute the OID `.1.3.6.1.2.1.2.2.1.2` (ifDescr), it returns the interface name. For example: eth7. …

specific mib to monitor with snmp-exporter the fans and the temperature of a sophos firewall XG

Hello. We have some way of collecting events related to IPS, AV-Detection, ATP, MDR and sending them externally to a zabbix-type application. I am using SNMP but this interface does not provide such resources.

I've found a number posts requesting assistance with this, but it appears that no one has had a win. We have multiple sites, all which have multiple WANs configured. In some cases, it's Active/Backup, in others, we are load balancing multiple WANs …

Hello, I have been trying and failing to get SNMP monitoring working for my Sophos XG firewall using PRTG. I have done the following to try and get this working: Enabled the SNMP agent in the firewall config Added the SNMP manager address and…

Is there any way to use SNMP to monitor traffic flow through an IPsec tunnel? I'm successfully capturing port traffic with SNMP but would also like to capture the traffic between our two sites via an IPsec tunnel.

Hello, Can someone help me with my Datto RMM Monitor for Sophos? The policies have been installed way back, but when we replaced the firewall from one of our sites, the Datto Sophos Monitoring is now offline. I am new to both Datto and Sophos community…

i enabled SNMP v2 agent on Sophos XG230 and successfully tested it from a remote server: snmpwalk -v2c -c mycstring 172.16.0.1 1.3.6.1.6.3.10.2.1.1.0 iso.3.6.1.6.3.10.2.1.1.0 = Hex-STRING: xxx then i enabled SNMP v3 (authentication only, no encryption…

I have: XG230 (SFOS 19.5.3 MR-3-Build652) XG125 (SFOS 19.5.2 MR-2-Build624) I searched in: CONFIGURE - System services (all available tabs there) SYSTEM - Administration (all available tabs there) google searche returns NOTHING or USELESS…

Hello everyone we are currently testing the shipment of SNMP V3 traps. Unfortunately, we notice that new engine IDs are constantly being sent by Sophos. Sending the traps with V2C works fine. I've been testing all morning and looking at the trap receiver…

Hi, Does anybody know what the OID and name is of the XGS WAN link manager is so I can monitor this with SNMP? I'm having trouble finding it in the MIB files.

Hi! Here in my company we have 4 address with Sophos Firewalls and in each Office we do have multiple internet links. We need to remotely monitor the individual gateway status from each firewall. Even on the version 20, Sophos offer the option to…

Hello. I would like to know if it is possible to monitor via SNMP protocol the APX120 and APX320 Access Points managed by a XGS3100 Firewall, and collect the information on a Zabbix server. I already monitor the XGS firewall with the SNMP agent with…

I'm trying to configure SNMP on Sophos Switches and I can't seem to get it working. Looking at the options and documentation it's pretty cryptic. SNMP - Sophos Switch documentation All I need is to set a community string, SNMP version and make it read…

I downloaded the Sophos MIB file and it contained MIBs for every sophos switch. From my knowledge, a MIB file contains many OIDs which represent values which can be monitored by a monitoring application. The MIB files looks very cryptic eterType…

I can't find a single how-to or example for setting up SMTPv3. Does someone have a working example? I am trying to get SNMP V3 on Sophos CS110-48FP to communicate with a Domontz agent. (SNMP Polling). Does switch have and logs which show relevant…

Hi; I want to do monitoring from snmp service but I don't want to open snmp service to the all world , I only want to allow snmp to the specific ip adress. for this process; I am going to system -> administration -> snmp and activated the snmp service…

Hello, I would like ask , if somebody know , if will be option monitor VPN IPsec via snmp or API. I found , that is offen question in the forum. Sophos XG - SNMP - Monitor tunnel status Check Ipsec Vpn Status by Command Cli Read IPSec Connection…

Hi all, we would like to monitor the currently connected number of ssl vpn users with PRTG. Unfortunately there seems to be no snmp oid for this - see SNMP - Number of VPN Users? Any other ways to access this value? Sophos API, SSH? Any plans to create…

I've tried using the two templates available in the zabbix repository, but without success. Both models do not support OIDs. I manage to communicate my firewall with Zabbix by SNMP, but it is not possible to communicate data because we don't have a template…

Hello, it looks like the XGS3100 is sending faulty snmpV3 traps. In order to check that I would like to enable the debugging log for the snmp deamon, There is a manual for the UTM but doesn't seem to be the same for the XG. https://support.sophos…

Guys, has anyone had success using grafana/zabbix with Sophos in version 19.5? I found little information about sophos and zabbix, a lot of material was developed for version 18, which is no longer functional, Sophos support nobody can help. Can anyone…

By default, the agent's port is 161 and the manager's port is 162, but many internet operators here in Brazil leave this port blocked, which makes it impossible to access the firewall's SNMP. How to change this default port?