Disclaimer : This information is provided as-is for the benefit of the Community. Please contact Sophos Professional Services if you require assistance with your specific environment. Table of Contents Overview Log Viewer Firewall (Invalid…

Hello Everyone, one of our customers has a phone system (Panasonic KX-NS700) that uses multicast to synchronize the Cell-Stations (KX-NS0154). The Cell-Stations (DECT) use PTP for synchronisation.There is one Master and several Slave-Stations. Although…

Good morning everyone, i'm trying to implement BGP over RBVPN, neighbors are up only when i add the comand disable-connected-check and if i use the comand maximu-path 20 they cannot establish, any advise? Also with the comand disable-connected-check both…

Hello everyone, How do i create a static route pointing to null0? I need that route to be a summary route so i can advertise it in bgp. Many Thanks, Dragos

We have 3 internet links; I want to route the web-based system (URL) through one of the WAN links. Please advice on how the routing should be configured. Whenever the user click on the link, it has to point to the dedicated WAN link.

We have a location where we have Sophos XG106 Firewall serving as Gateway. We have one MPLS link on the location. We are facing issue when we shift / redirect traffic on MPLS link to connect to HO. Static routes are working fine. We are able to reach…

Hi, we have a client, We created a VLAN on a MPLS VPN for a site branch to access the internet from the head office. We have two branches connected under the same VLAN ID. the other one is working successfully, but the other branch is connected but…

Hello, I'm stuck on a LAN routing problem. We changed our UTM firewall to XGS116, I recreated the rules and configuration on the new firewall, but I have a problem with the incoming traffic to the internal network. We have several offices that are interconnected…

Hi, I have a networking related question. I'm not sure if it's a configuration issue on the Sophos firewall. I have a Sophos XGS 136 appliance with a number of physical interfaces configured with the following IP addresses: 192.168.100.1 and 192…

As I've worked through some (not all) setup issues, one that continues to stump me is the fact that when my NAS is connected to switch along with all other LAN devices and incoming internet from router, life is good. I can access my NAS no problem. …

Hello there, I’m trying and failing to route all internet traffic from device 10.5.15.20 at SITE B across the layer 2 MAN and out ISP1 WAN at SITE A. I’m trying not to impact any other traffic at SITE B with this configuration, only internet bound…

Hello Everyone, Apart from Sophos SSL VPN, I have a Centos based OpenVPN server, which is behind my firewall. My OpenVPN clients access that server through a DNAT rule. I have created a VPN tunnel (Site-to-Site) between Sophos XG and AWS, using this…

Hello everybody, can these two devices work together? And if it is possible, what is the best way to connect this UDMP to Sophos? At the moment customer is using UDMP as router/firewall. Thanks

Hello, I have bought my first Sophos Firewall and I need some help. Setup: Port1: LAN - 172.16.0.1/23 Port2: WAN - Public IP (PPPoE) Port3: LAN - 192.168.1.1/24 Site-to-Site IPsec tunnel: Port1 172.16.0.1 (local site) - 192.168.0.1/22 (remote…

Hi there, I have no experience with Sophos firewalls. I recently purchased XG 125 for a small office. I have done the initial set up and the device is connected to the internet. I connected a level one switch (unmanaged) to the one of the LAN ports…

Setup Sophos XG 330: LAN Port 9 10.0.0.248/24 LAN Port 9.8 10.0.8.248/24 FIREWALL RULE: LAN any - LAN any ALLOW Port 9 plugged in Switch port 24 Layer3 Switch: VLAN 0 10.0.0.1/24 VLAN 8 10.0.8.1/24 Port 24 Trunk ALLOW ALL VLAN Port 1 VLAN=0 Port 2 VLAN…

Hello, i have a problem and i hope you can help me: 1) I have a zone called >RED, with my REDs in branch offices (Ip-network: 192.168.41.1/24) 2) I have some destinitions which are connected with IP-Sec connections (IP-Network: 172.30.200.0/24…

Hello, I apologize if this is a rookie question. I have 2 XG 430s in HA mode behind a Cisco 3900 router. ISP>Cisco>XG>Users My question is can we use the Firewall(s) for routing and eliminate the Cisco router? I believe it's only doing layer 3 routing…

I've tried to follow rfcat_vk's excellent documentation of the current state of IPv6 in SFOS. And I've been feeling like I'm missing out that my ISP doesn't offer IPv6 (they've said "coming soon" for a year now, maybe more). But the more I look into it…

Hi All, newbie in Networking. Currently, we have this network setup We are planning to get an additional ISP exclusive for one of our departments. Is it possible to connect another modem(ISP) to our router and which configurations should I do to…

Hi everyone, Maybe I'm doing something wrong but I can not have all my offices browse each other on MPLS connection... First of all each office has a connection, managed externally by one ISP, with its own router and each is part of a big MPLS. On…

Hello everyone, Sorry for being a noob here. I have the following network map layout: I use a dual-WAN bandwidth aggregation configuration rather than a failover one for most of the interfaces. However, I look forward to: Assign my TrueNAS server…

Am I missing something here ? I've installed Debian 3cx and Gateway is Sophos XG (static ip and gateway set on network)... however even without Sophos running i can still get normal access to 3CX just fine, which proves despite setting static IP and…

Hello I have two sophos connect together. Sophos1 - switch - Sophos2 I have multiple VLANS between them. All vlans have owen subnet. Phisical interface has also owen subnet. I cant ping betwen vlan interface. Whatever i use. But Phisical interface…

Hi, I'm attempting to get WAN failover working across sites using OSPF (default information originate). The issue is with getting the local default route disabled in case the local Internet connection drops. Can you please let me know what is the correct…