Hallo, ich habe hier ein seltsames Phänomen. In einer Windows Domain (192.168.2.0/24, Zone LAN) braucht ein Windows 11 Client für den User Logon zwischen 2-3 Sekunden. Nun habe ich ein VLAN3 (172.17.3.0/24) mit der ZONE VLAN3 erstellt, der DHCP Server…

Hi all, i installed Sophos on hyper-v (vm) with 3 NIC: - NIC-A “LAN” (physical nic on server) - NIC-B “WAN” (physical nic on server) - NIC-C “LAN” (private virtual switch hyper-v) I’ve created Bridge with NIC-A and NIC-C, with "enable routing…

Good day Members, I trust you are well. We are trying to setup a guest Wi-Fi with Sophos and Unifi. We have it currently working but with the DHCP server on the DC, We would like to move the Guest Wi-Fi DHCP to the Sophos XG. Main issue is device are…

XG210, SFOS 19.5.2 MR-2-Build624 So, I have two VLANs, VLAN 70 - 192.168.70.0/28 and VLAN 100 - 10.0.0.0/24. DHCP server is on VLAN100, I want to relay DHCP requests from VLAN70 to VLAN100 for service. I have a relay set up like so: Name …

I have a small problem, I have a mikrotik router set up wlan10 (10.10.10.1/24) on port 2 everything works, I connect directly to the router, I have access to the network via vlan10, and when I connect sophos home (in bridge mode), I have an address assigned…

i have dns domain server 10.0.0.1 mask 255.0.0.0 gateway 10.0.0.2 & and ip range is 10.0.0.1 to 10.0.0.254 but now i want to give different ip range to different department like 10.0.1.1 to 10.0.1.254 to support department and 10.0.2.1 to 10.0.2.254 for…

Hi, Sample: configured sophos XG135 VLAN1 to go through port 1 of the firewall , how do i set it to use port 3 and 4 on switch for VLAN1. VLAN1 goes though port 1 on firewall then port 3 and 4 on the switch connected . Port 1 part is done, how…

I just cannot figure this out now. Been trying this for a day and desperately need your advice on this. I am trying to build a simple separated (isolated) VLAN from Ubiquiti Unifi AP Network to Internet route: Unifi AP -> Unifi Switch -> Sophos XG.…

Hello, I created a VLAN for my WAN interface. I see the IP in my FritzBox but the Gateway in the Sophos XG Home is offline. The ping check under "diagnostic" failed, too. Fritzbox Network Interfaces Gateway

Good day everyone, I have been asked to update our network so our data demands can be met. Currently, we run a conventional flat network and our Sophos XG is routing all the traffic. THru my research I think the best solution is to design the network…

I followed this helfull guide: Sophos Firewall: Interface / VLAN Migration via XML Import/Export I am facing a migration from SG (UTM) to XGS (SFOS) with hundrets of VLANs an DHCP-Server. Sophos Migration Support converted the config of the SG and…

Currently, I created Vlans for my each SSID of my Unifi APs. I have 4 APs, all connected to my TP-Link poe switch, which is Vlan aware also. The poe switch is plugged to my Cisco switch e.g. port 10 (Vlan aware). All other desktops (not in Vlans), NAS…

Hi all! Quick question regarding XGS 126: MTU is a property of the physical interface. If I want to reduce the MTU for a VLAN I have to do it on the physical interface. By adjusting MTU value I seem to lose the VLAN interface and the associated dependencies…

Hello, i have a problem with the internet connection on physical port WAN with additional vlan (zone LAN). I tried to change the physical port to an dummy ip and zone DMZ and create two vlans 1 (WAN) and 40 (LAN). My router recognizes the IP address…

Hi, We have just started using Sophos FW and having some difficulties creating Rules. We have two vLANs vLAN10 and vLAN20. We need to allow vLAN10 to have full access to the internet whereas vLAN20 should have a whitelist, i.e. access to few websites…

How many maximum VLANs support in XGS3100 and XGS4500?

Hi, I'm new with this equipments, i'm trying to configure VLANS between two equipments (SOPHOS -» Switch) SOPHOS: - WAN - DHCP from ISP router - LAN PORT1 IP: 192.168.100.1/24 - ZONE LAN 1.10 - VLAN 10 - 192.168.10.1/24 - PORT 1 - ZONE…

Dear Sir, i have already configure VLAN but i am not able to connected vlan to lan can you please help us and resolve this issue asap

Hello all, Currently, we need to migrate our existing Firewall Watch Guard Router whose license will expire soon by the Sophos Firewall. So we ask for your help to set up a trunk between these two routers, indeed the idea is that the Sophos will play…

Hi All I would like to create a Lan trunk between the Sophos XG Firewall and the Cisco Router This is my topology Could you please help me

Hi all, User Kyle Sexson had this issue a while ago, too, but there’s no solution in his post - so… I have a set of VLANs running on a bridge interface. This works mostly well, but certain outgoing traffic will show up both on the bridge interface…

Hello, I'm new to Sophos and can't seem to figure out what I'm doing wrong. I created a separate VLAN (Port 1.50) to prevent my IP cameras from accessing the internet and added the VLAN to the default "Traffic to WAN" group, rejecting any internet traffic…

My setup has 2 VLANs - Main and IoT, using Sophos XG as DHCP and gateway. I'm able to allow traffic between the 2 VLANs by adding a firewall rule of LAN Any host Any service to LAN Any host Any service. What I'm trying to do is to only allow traffic…

Hi, I have increased the size of a subnet from /27 to /26 and any node with an IP beyond the range of /27 has connectivity issues. I have done this before and don't remember having issues. Apart from Network > Interfaces > VLAN > {Port} > IPv4/netmask…

I see an IPv6 address on my WAN port, but none on any of my configured VLANs or Interfaces. I'm guessing I need to configure IPv6 Router Advertisements, but when I click it doesn't have an interface I'm not sure how to open this port up for these…