Browse By Tags

After I set up a RED20, I plugged an AP into it, as I wanted to have an AP behind the RED20. I have it in Split-Tunnel Mode. The issue I had was that the AP would not show up in the list of new APs to authorize, on the UTM side. I read many many posts…

Hello Community, We are trying to connect a RED 10 to a new UTM 9.509-3 I added it with all needed information and now i get this Error: Self: Failed to open Private Key error:0906D06C:PEM routines:PEM_read_bio:no start line error:140B0009:SSL routines…

Hi, I have a astaro red 10 (maybe rev1 manufactured in 2010). Yesterday it stop working. After a power off/on , i have (led): power : fix green system : fix green internet : led off tunnel : led off Lan 1 to 4 : fix green I use only wan…

Hi, I'm soon rolling out a bunch of RED 10s and have a question regarding the WAN setup and RED Fallback. In UTM9 WAN Settings for REDs you can setup a Static IP. I was wondering wether i can input a public IP or not (so i don't need a Router in…

Hallo, ich habe eine UTM9.5 172.17.2.1/24(PPPoE und DYNDNS) und eine RED10 172.17.3.1/24 (RED steht hinter einem Router, Unitymedia FritzBox) Tunnel steht. Beide haben einen DNS & DHCP Server. Ich habe eine Maskierungsregel von UTM-> RED und von…

Hi, one of our customers has the problem, that without RED tunnel comp. it is not possible to do ICMP larger than 1380bytes. When i activate compression the ICMP goes through - even with 9000bytes. i double checked everything, also went through…

Hi, I picked out an older RED 10 and plugged these in my external Network (in front of my utm, not behind) to test these bevor driving to my new remote office. The RED semes to be working but after a short time the System LED begin to blink red and…

Hello everyone, I just added a RED10 to our UTM9 and chose Standard/Unified mode as we need the remote office to be working via the local office's public IP address. However, the remote office's clients shall not be able to access devices such as…

Be careful with the update to 9.411. The update kills the config of the RED10 with static IPs! The REDs will act as DHCP-device after rebooting/firmwareupdate. This update killed 3 devices with static IPs - I had to put it in a router with DHCP and…

Hallo, heute wurde auf zwei Unabhängige UTM Systeme die aktuelle Firmware aufgespielt. Jeder der UTM's hat ein RED10 Gerät verbunden. An beiden UTM's kommen die RED10 Systeme nicht mehr Online nach dem Upgrade. Kennt jemand dieses Problem? Bis jetzt…

hi all first thank you for accepting me to this group second i have UTM 9 at the main location, and branches have red10 the IP address at the remote offices shows the additional address that configured to this office at the UTM example …

Hello everybody, We have two branch offices that connect to our company network through RED 10 devices. Recently, one of these two has started experiencing problems where the tunnel will fail every couple of hours. Note that only of the offices…

Hi All, Thanks for reading.. I'm new to working with a RED 50 and RED 10 both connected to a UTM9. Due to the way the different networks were constructed, they are as follows: UTM (local 192.168.8.4) -> RED 10 -> local IP 192.168.9.1 RED 50 -…

Followed instructions according to www.sophos.com/.../116573.aspx (Standard/Unified Mode). Connected RED10 to remote site, but I think it keeps rebooting. Power light stays on, 30 seconds later System light is on en 15 seconds later Internet light comes…

i have a RED 10 v1 from an older installation that we want to repurpose. We connected the RED on a seperate Router and according to the LED lights it requested an IP Adress via DHCP. The RED has been configured with ID and unlock code for the provisioning…

I upgraded the UTM to a newer bit of hardware and restored the config just using a backup/restore (without License, passwords, certificates/keys, endpoints) when I switch over to the new device everything works fine apart from the RED10 endpoints don…