Almost 20 seconds elapsed from the instant when you click apply to the instant you get back to Firewall rule page?
Guys, I hope that you track this as a bug and improve the performance.
I know this doesn't add any further to your request but the system load of almost 100 percent per core is unsustainable in a production firewall. I was running system load over 3 on my test firewall in a vm with quad cores. Yes throwing newer, faster hardware will bring it down a little but the system load has increased significantly in v18 compared to v17 and my test lab had only one user mostly playing with the GUI.
I would expect that some of this is related to the performance of the hardware / VM.
I have only used Sophos VM's in the training environment. All my customers are using XG Hardware.
I know that the customers I have with an XG210 and an XG310 are far more responsive in the UI and rule creation than the XG125 that I use in my office.
I also do not have a single customer with anything smaller than an XG125. From back in the Cyberoam days, I installed a single CR15, found it so painfully slow then and lacking the report engine I never ordered another. I have kept this through to today.
Gavin Daniels. DipIT(Networking)
The main dashboard takes nearly a minute to load every widget on the screen. When you create a new firewall rule, the menues are also very sluggish.
Should there be an significant perforcamance/appeareance improvement for the UI adressed with "project Picasso" for v18?
If I am not wrong - my memory being outrageously unreliable - not long ago, you were asking the rest of the community for some understanding while v18 took so much time, because, mainly, v18 implied a full core re-write. Have you seen such thing happening somewhere ?
Besides the obvious few left and right, I did not spot any mountain moved.
We are clueless mainly because technical Sophos' communications are shutdown. And when they are not, it is merely a list of foggy concepts that taste mostly like marketing pie.
Yesterday, few users in few posts ask what was in some technical bulletins fixing scary names vulnerabilities only to be answered, again, with a link to a criminally generic WEB page.
No one can take sound technical decisions informed like this. So every decision becomes like playing Russian wheel on an act of faith.
So Project Picasso is yet another thing that risks to provoke no excitement.
You know that story of a kid who was screaming "A Wolf !!!" a little too often with the end result that the same kid failed to attract attention while it was most important ?
Honestly i don't think Sophos changed the core right now, even there was some rumors they will do with v18. Same thing for project picasso. The GUI is still the same with long response times.
But as we are all investing our time in testing v18, i think it would be fair, when someone from Sophos could explain what's up with the "core re-write story" and "project picasso". [:O]
Thanks for your answer.
I presume this would be questions for this event: https://community.sophos.com/products/xg-firewall/sfos-eap/sfos-v18-early-access-program/b/blog/posts/webcast-firewall-v18-overview-and-live-q-a-with-the-xg-product-team---november-14-11am-est
It would be preferable someone more polite and nuanced than I ask. Cause I have a tendency to be aggressively unforgiving in my speeches when I'm not delivered in time what I rightfully expect since it was promised ages ago. I'm stuck at WWII thinking era. Kind of "If you don't you die".
Picasso? I think we are still trying to find nemo.
Kidding aside, Sophos should do themselves a favor and acknowledge v18 with respect to the internal code names floating around. Is this the result of nemo?? Boy I sure hope not. Cause from what I see nemo isn't done and picasso hasn't even started. Just my eyeball test though.
Even more challenging, I built the J1900 from V18 EAP refresh 1 update ISO, what a pain. Different install screens, lots of blank screen while something is happening, no indication of activity, enough of that this thread is about performance.
You thought the upgrade from v17.5.8 was slow this is even slower. Some items never complete a change, I have been trying to update etc notification settings for at least two hours including restart to see if that unstuck it, but no, still the magic circle.
Can someone form Sophos devs look at this issue?
I have isolated the issue to W10 PC and IE.
I have used the same software build on two different versions of hardware with the same issue, so that left the management PC as a likely cause. Checked using FF on MBP and all the settings are correct and no spinning ball.
No body from Sophos is considering this thread?
This is a performance issue. Editing an existing firewall rule still require 14 seconds to update. Can this be tracked and investigate?
I am the only one with this issue?
Maybe is my installation? Can someone from forum confirm the behaviour?
Hi Luk, I tested this with a stopwatch [8-|] . I have a 4GB vm with 2vcpus and memory utilization to 80%. I have web proxy with categorization and av blocking. Also running Application categorization with allow all for pretty graphs (not blocking any apps). I don't have any DPI rules. I am also not using IPS.
Average time for a rule update is 10.85 seconds. I did the test multiple times with different rules and it is always 10.5 plus seconds. I usually don't play with the firewall once its setup so not a problem after initial setup. I am also getting some inconsistent results with multiple NAT rules as the firewall seems to get confused if you turn on and off too many rules but that is not the topic here.
Are you running everything on your firewall? Maybe the processor is overwhelmed with everything running? Not saying they don't need to fix this, just wondering why you are getting almost twice the time that I am getting on firewall rule update.
10s? This is a "huge" amount of time. Updating a firewall rule should not require more than 4/5 seconds.
I think the gui waits for the backend to finish before it says update successful. Its the same behavior if you turn on a service that is not running. Turn off IPS and then turn it back on, you will have to wait forever before the service started message comes up.
I agree that overall gui is too slow from control center to firewall rules. Was v17 like this? I don't quite remember how the older v16.xx versions acted on rule updates but from memory, they were still slow compared to other firewalls
...they were still slow compared to other firewalls
...they were still slow compared to other firewalls
That's the problem. I lost already 2 customers and 5 are waiting for UI responsiveness in v18, otherwise they will move away. Same behaviour for logging. There is a certain lag between what's happening and log itself (I do not want to say nothing about the logging quality via UI).
I am currently working with CM as a GUI replacement and it is quite fast.
Did you try this approach?
No Lucar. Small customers do not need CM. They use XG interface.
Is CM going to be the new UI even for XG in 18 or 18.5?
can you ask to some dev like Rana Sharma or someone else to look at this issue?
The basic question is: Is it slower than V17?
The title of the thread is clear! In v18 no improvements have been done for speed-up Firewall editing UI.