Hi all, when we try to add or change a configuration on the IPsec settings page on our XG/XGS Firewalls we always have to wait for about 2 minutes for the site to load and for it to be usable. The web browser shows the message "This page is slowing…

Hi all, AP configuration works. I am able to remove & add the AP's. AP's are recognized and shown as active. I can see the traffic between AP & XGS Port 2712. Traffic to port 8472 from firewall to AP is not answered, but i see packets from AP to APIPA…

After update to my xg firewall to v20 ipsec is become unstable. Randomly disconnection. openvpn client work without issue only ipsec have problem Some info: this setup worked for 2 year without a problem (another bug on v19 but fixed). Sophos firewall…

Hello @all, it is known that with IKEv1 on SFOS a new PSK overwrites all others PSKs if the gateways do not differ in the connections. Sadly I can not use IKEv2. Is it sufficient if just the local ID is different in connections and the remote ID is ANY…

Good morning. I have several XG/XGS of different clients configured with IPSEC against the same central, this central uses a CISCO firewall (we do not manage it). The problem we have is that every 30 minutes we receive an email from all the XG/XGS indicating…

Hi, What is the proper way to connect a branch having multiple internet gateways but the head office has only one gateway? The branch office WAN1 interface has a Real IP but WAN2 uses DDNS with a dynamic IP. Should the branch office have a failover…

Hi, One of my IPsec tunnels shows a yellow icon under the status but when I click on the connection details, all subnet connections show green. Any Suggestions?

Hi, We've run a flat lan for years at our main location. We've recently updated our network and added a few new VLANS to the mix. Now I have a problem. We have several Site-to-Site VPNs up and running that work great with our original VLAN1. However…

Hello, can you continue to use the SGs at the secondary locations as RED devices with an XGS or should you switch to an SD-RED 20 or SD-RED 60? Thank you very much

Hello - I have an XGS 2100 at HQ. We were using a RED device to connect the branch office Phone and LAN traffic via VPN to the HQ PBX/LAN and everything worked fine. Given the rollout of the latest OS, the RED is no longer compatible, so we are attempting…

Hi, I have a Sophos XGS107 (SFOS 20.0.1 MR-1-Build342) setup with Site to Site vpn to a Mikrotik router. There is 4 vpn tunnels (or separate address pairs), It mostly works fine, but every other day one tunnel goes down. If I check in webgui >> site…

Hi all, we currently have 20 sites all using Sophos XG107 or XG 117 FW. all sites have a S2S VPN connection into AWS for SMB access. issue we have is failover internet, if failover is required then our VPN drops due to new IP. Failover internet is…

Hi, Are there any specific IPSec Profile recommendations for connecting the branch office that does not have a static real IP Address? I am currently using the DefaultBranchOffice profile, but it disconnects automatically after some time. Thanks.

Hello all, I have a situation with a IPsec VPN setup between two sites that have subnets that are the same. I followed these instructions and it worked ok; NAT with route-based IPsec when local and remote subnets are the same - Sophos Firewall However…

Hello all, we are looking at a situation where we need to set up a site to site VPN to a vendor who is using a Fortigate gateway, and the same subnet is being used at both ends. I have reviewed the below link which covers this situation for Sophos to…

Hello, we are currently using Sophos Firewalls in a Hub-and-Spoke topology running SFOS 20.0. Some spokes are using WAN connections with dynamic IPs which will change from time to time. On those units we can observe that the corresponding XFRM interface…

Hello, We are having problems establishing an IPSEC tunnel between an XGS and a Fortigate firewall. Currently we receive the message “IKE SA proposals don't match. Check the phase 1 policy settings on both devices: IKE:AES_CBC_256/HMAC_MD5_96/PRF_HMAC_MD5…

Hello, Im trying to test out Cloudflare magicwan and the guide says to disable ipsec anti replay protection. The guide shows a command for sfos v19 however this doesn't seem to exist in v20. The command is: set vpn ipsec-performance-setting anti…

Hello, we have set up several Policy Based IPSEc tunnels. These have different remote gateways, but some of them have the same remote IDs. Some connections crash after a certain time. Could this be due to the PSK in conjunction with the remote ID? As…

I have something strange for the following situation. VPN connection between site A and site B (tried both policy-based and route-based) and a policy-based VPN-connection between site B and site C. Intention is to reach site C from site A while there…

We have currently have two locations, each with a XG330 v19.5.4 MR4 and an EPL fiber connection between them that has a S2S IPSec tunnel setup and a static route on both ends pointing to the other. Each FW is setup with the local DC for user authentication…

Hello, I want to setup a S2S IPsec VPN between our Head office and Branch Office. The branch office has only IPv6. I have setup on btoh side the S2S VPN, but i cant get it to connect. And i even dont see any connection trys in the logs. For all other…

I don't know if this is the right configuration so bear with me. I have a connection that essentially functions as a direct ethernet line back to the main office, called an EPLAN. It is set up in my Branch Office in the LAN zone. Everything works OK…

How can I disable MOBIKE IKEv2 extension support in IPSec?

Hi, is it possible to clear single IPSEC VPN security associations via Device Console or Advanced Shell on Sophos XGS? E.g. I would like to disconnect all VPNs to one specific gateway. Thank you. Greetings, Torsten