Hi guys There is one thing that caught my attention, What does Received drops mean? Thank you

Hello everyone here i check documents and dont found how to do this. I tried to did Ethernet card test XGS but i found this article https://support.sophos.com/support/s/article/KB-000036345?language=en_US&c__displayLanguage=en_US and saw dont…

Hello, I am James from Chicago and I run a how-to base tech site ; I am facing some problems sending and receiving emails to the internet; an XG requires a smart host upstream. My issue is that the XG already sends outgoing emails on the appropriate…

I have Ports 2 and Port 4 configured as WAN, both active with weighting of 1. Both are connected to Comcast BUT separate internet connections, one is from my house, one from next door. It appears by Speed Testing that both are passing download traffic…

10GbE Fiber Transceiver Short Range is compatible with Cisco Meraki series or not

Greeting SOPHOS Comunity, I am looking for some help configuring routing on a Sophos XG 135 SFOS 19.0.0 GA-Build317. I don’t work on firewalls often, so I apologize if some terms are incorrect. I did find https://community.sophos.com/utm-firewall…

Hey, I am trying to find a way to send the WOL packet to computers connected to my XGS116. I have a bunch of work stations Intel Nucs on VLAN100 and some servers etc on VLAN200. I want to be able to turn them on remotely via WOL. The issue is, I…

Hi folks, early this morning my Australian nbn connection failed. When restored the internal networks were not able to access the internet even though the wan status up. The issue being the XG did not request a new a new address. I restarted the nbn…

How can I get more ports on XG 230 if they are full?

Hi - I have a Sophos XG 135 and I have set up two different networks with different Gateway IP addresses. Port 1 uses 192.168.1.1 Port 8 uses 10.150.121.1 Port 2 is the WAN port I would like devices associated with Port 1 to be able to communicate…

I mistakenly made the Port2 interface my backup WAN, and Port4 my primary. As a consequence, the SSL VPN always prefers Port2 first, which is not as fast or stable, so I have to edit the user VPN config to move up the Port4 WAN to first in the config…

We have two lease line links configured on Sophos XGS 3100 firewall out of which the link of one of the lease line link goes down automatically after every 3-4 hours that too after changing weight of lease lines or changing fail over rules. Looking for…

Hi I need asistance pertinent to the process of configuration for Sophos XG Firewall on a VM Ware platform. Currently I have Workstation Player 16 with a Windows 2019 Server , I created the Sophos XG VM apart. I would like to know the process of integration…

Hi, I thought creating a Bridge on XGS-136, for example, creates a "switch" between bridged ports, but either I do not understand principle, or reality does not follow the principle - I found no, bridged ports do not behave like switched ports. For…

Hello, I have some issues with the management port which is in the same network as a management network that I want to "hide" behind the firewall. I changed some routing (on 10 GBit Port) with resulted into two interfaces on the firewall in the…

Hi, we recently replaced a UTM firewall with a XGS126 (SFOS 19.0.0 GA-Build317). We haven't changed anything else, the network config is the same. On this site we have a 10Mbps WAN link and two 2Mbps MPLS links (active-passive). We are ICMP monitoring…

GREETING!!! 1. I have site-1 and site-2 with there own sophos xg firewall connected to wan link on port-8, port-1 is on lan, and port-f1 uplink is connected on both sides. so what rule should i create to bypass the traffic from site 1 to site 2…

Hi all xg sophos FW Please look at picture below I don't know how can i read this config I know it's LS link, but there are 3 ip adresses: 01 private configured with its GW, and 02 others ip public (real ip). When you edit these 02 ip adresses…

Someone has a hint: I can't remove the network settings from a base interface on which Vlans are configured. At first I thought this configuration is not possible, but it is possible to configure it like this. To make it clear to images with the…

Hi, we have 3 HA Active/Passive Clusters with XGS136. They all have Port10 as dedicated HA Port and are linked with 1m patch cables of good quality. All 6 nodes show dropped packets and some also show port errors on Port10 for RX only. Some of…

The following is the error in firewall log which showing RX State: packets errors:8 dropped:58662, please help to solve this issue. port 1 UP BROADCAST RUNNING MULTICAST RX State: packets:169291044 bytes:41103398907 (38.2 GiB) errors:8 dropped:58662…

I have 2 firewalls that were at the same client. There was a thunderstorm that rolled through and it seems that they were hit. So I am verifying that the firewall was damaged. Both units are XG 115W. They have 4 physical ports. Port 1 no longer works…

Hi All, When trying to configure the PPPOE i'm getting this error " Remote message: User not found." but i'm sure the user and password are working fine, is there something i can do? /Thanks pppd 2.4.7 started by root, uid 0 PPP session…

One of Our customers using Sophos XG 230 V 19.0.0 firewall and configured 03 WAN links (One for backup and Two for Active-Active Load Balancing) but after the configuration one of the Active-active links went frequently and sometimes it always indicated…

Hi, In my logs, I'm getting a huge amount of Invalid Traffic event. This started to happen when, by mistake, I changed the MTU on my WAN interface. It used to be at 1500, and now, when I set it back to 1500, internet doesn't seem to work properly…