Thread Info
  • State Suggested Answer
  • Locked Locked
  • Replies 5 replies
  • Answers 1 answer
  • Subscribers 38 subscribers
  • Views 1595 views
  • Users 0 members are here
Options
Suggested
This discussion has been locked.
You can no longer post new replies to this discussion. If you have a question you can start a new discussion

Multiple PUBLIC IP leashed line setup for NAT

ywillie

Hi .
I'm having trouble trying to get one of the Public IP(Alias) to be nat onto voice subnet interface.
Here's the diagram below.
Network Diagram.

Here's what i configure for the Leased IP Line.

For voice LAN interface Subnet i configure as below.

As for rule. I did it as below.

I have trouble reaching 202.111.122.113 via 4000 to 4008.

May i know which settings i did wrong or is there something i left out ?




This thread was automatically locked due to age.
Parents
  • 0

    Hi ywillie,

    As per configuration screenshot, Use Outbound Address seems to be incorrect as this rule is for allowing traffic from WAN(XG-A1) to PABX so there is no need for NATing it with IP 202.111.122.113, you can either uncheck "Rewrite source address" of select Rewrite source address as MASQ instead of 202.111.122.113.

    Regards,
    Hardik R

     
  • 0 in reply to HardikR

    My home internet using dynamic ip. It's currently recorded as 63.44.113.222.
    As i did the test. SRC IP:63.44.113.222 to 202.111.122.113 actually passes the traffic.


    However.
    When i reverse the results with only 
    SRC IP:202.111.122.113 .
    It returned no results.
    I tried
    SRC IP:172.20.110.11 which is the pabx IP.
    It returned no results either.

    However when i tried SRC IP:172.20.110.10.
    It returned something.


    Seems to me that the router is the culprit.
    It's a TPLINK R600 router.

    The TPLINK router was used as a SIP dial up device. It has 1 WAN port connected to the SIP Service provider's modem.
    While the entire LAN network were setup as 172.20.110.0/24 on the TPLINK R600 Router.

    I figured that if request the vendor to configure the entire network to be 172.20.110.0/24 on the TPLINK R600 router,
    It'll actually allow traffic across the firewall towards 202.111.122.113 by creating a DNAT Rule.
    However that's not the case.
    This is an actual view on the PABX and it's related devices.


    There's a static routing missing at the TPLINK Router R600 side.
    Could i get a help on static routing part ?
    Should i route only 172.20.110.11/24 accross to 202.111.122.113 ?
    I had another concern would be by doing such a static route, it might even change the path of the MLS causing the SIP traffic to not work properly..

Reply
  • 0 in reply to HardikR

    My home internet using dynamic ip. It's currently recorded as 63.44.113.222.
    As i did the test. SRC IP:63.44.113.222 to 202.111.122.113 actually passes the traffic.


    However.
    When i reverse the results with only 
    SRC IP:202.111.122.113 .
    It returned no results.
    I tried
    SRC IP:172.20.110.11 which is the pabx IP.
    It returned no results either.

    However when i tried SRC IP:172.20.110.10.
    It returned something.


    Seems to me that the router is the culprit.
    It's a TPLINK R600 router.

    The TPLINK router was used as a SIP dial up device. It has 1 WAN port connected to the SIP Service provider's modem.
    While the entire LAN network were setup as 172.20.110.0/24 on the TPLINK R600 Router.

    I figured that if request the vendor to configure the entire network to be 172.20.110.0/24 on the TPLINK R600 router,
    It'll actually allow traffic across the firewall towards 202.111.122.113 by creating a DNAT Rule.
    However that's not the case.
    This is an actual view on the PABX and it's related devices.


    There's a static routing missing at the TPLINK Router R600 side.
    Could i get a help on static routing part ?
    Should i route only 172.20.110.11/24 accross to 202.111.122.113 ?
    I had another concern would be by doing such a static route, it might even change the path of the MLS causing the SIP traffic to not work properly..

Children
No Data
Unfiltered HTML