This discussion has been locked.

You can no longer post new replies to this discussion. If you have a question you can start a new discussion

Unable to setup an Awair Glow device

I have an Awair Glow device I purchased a few years ago that monitors the air quality in a room. It connects to the network via WiFi and it's worked great until a few months ago. I noticed it was having issues with staying connected to the WiFi access point, so I performed a factory reset to see if maybe that would resolve it. I've done factory resets in the past without any issues. However, I think this was the first time I tried since running Sophos v18 (EAP at the time). It connects to the WiFi network just fine, but when I try to continue the setup process where it communicates with the Awair server, it basically says the connection could not be established. I've tried:

Disabling ATP
Setting all policies to None and unchecking all scanning (basically a "clean" firewall rule)
Connecting to both my primary and guest network
Factory reseting the device several times
Disabling my ad-blocker (PiHole)

It still does not work. If I pair it to my phone as a hotspot, it works just fine. Anyone else out there with an Awair device on Sophos v18? I'm at a loss with this one.

This thread was automatically locked due to age.

Parents

0 rfcat_vk over 4 years ago

Hi Shred,

have you setup the modified default firewall block 0 so you can see what is being dropped?

Required WiFi Specifications

Glow is only compatible with 2.4GHz B/G/N WiFi networks. Glow can operate on dual band routers (2.4GHz and 5GHz), but we recommend giving each band a separate SSID before connecting to the 2.4GHz network. We also recommend turning off the load balancing feature for dual routers, as this can occasionally move Glow to the 5GHz network. Your firewall must also allow access to TCP ports 8883, 123, and 443.

Ian

XG115W - v20.0.2 MR-2 - Home

XG on VM 8 - v21 GA

If a post solves your question please use the 'Verify Answer' button.
Cancel
Vote Up 0 Vote Down

Cancel
0 shred over 4 years ago in reply to rfcat_vk

Yeah, it’s on a separate VLAN and I turned on logging for that firewall rule. I don’t see anything being dropped.

---

Sophos XG guides for home users: https://shred086.wordpress.com/
Cancel
Vote Up 0 Vote Down

Cancel
0 shred over 4 years ago in reply to Keyur

Yes, I see the IP address being registered by the DHCP server. The only thing I see in the firewall logs is an attempt to connect to a destination IP of 8.8.8.8 on UDP Port 53 (DNS) and both 52.26.177.117 and 52.40.15.135 on TCP 443. I did a packet capture from the Diagnostics page and this is what I'm seeing:

---

Sophos XG guides for home users: https://shred086.wordpress.com/
Cancel
Vote Up 0 Vote Down

Cancel
0 shred over 4 years ago in reply to shred

I've tried everything I can possible think of with this one. It works perfectly fine when I pair it to my phone as hot spot, so I'm fairly confident the device is fine. It never had any issues on Sophos XG v17, so something under the hood with v18 it does not like.

---

Sophos XG guides for home users: https://shred086.wordpress.com/
Cancel
Vote Up 0 Vote Down

Cancel
0 LuCar Toni over 4 years ago in reply to shred

Did you try to disable the DPI Engine? (Disable and / or the Off Switch - Try both).

Do you see something in the TLS Logviewer?

__________________________________________________________________________________________________________________
Cancel
Vote Up 0 Vote Down

Cancel
0 shred over 4 years ago in reply to LuCar Toni

Hm, I did try all that before but I just gave it a shot again and it seems after disabling SSL/TLS inspection by turning the entire thing off, it's now able to connect. I'm confused as to why this is though. This device is on a separate VLAN and separate firewall rule that does not have SSL/TLS scanning enabled, so why is this setting affecting that firewall rule? This separate VLAN is for my guest network and only has one firewall rule, which has no scanning at all.

---

Sophos XG guides for home users: https://shred086.wordpress.com/
Cancel
Vote Up 0 Vote Down

Cancel
0 rfcat_vk over 4 years ago in reply to shred

Hi Shred,

SSL/TLS scanning happens on all none proxy rules according to the experts.

Ian

XG115W - v20.0.2 MR-2 - Home

XG on VM 8 - v21 GA

If a post solves your question please use the 'Verify Answer' button.
Cancel
Vote Up 0 Vote Down

Cancel
0 RickardNordahl over 4 years ago in reply to shred

You should be able to make an exclution for your device for the DPI engine.

https://community.sophos.com/products/xg-firewall/f/recommended-reads/115976/sophos-xg-firewall-v18-xstream---the-new-dpi-engine-for-web-proxy-explained

//Rickard
Cancel
Vote Up 0 Vote Down

Cancel
0 shred over 4 years ago in reply to RickardNordahl
I guess I no longer understand how Sophos XG works.

If I have a device with:

All policies set to None on the firewall rule

All options under Web Filtering deselected on the firewall rule

No SSL/TLS inspection rule defined

ATP turned off

My understanding is that is no longer using the DPI engine or proxy.

Can someone explain how the DPI engine is still being used?

Secondly, why would turning SSL/TLS inspection to off make any difference for a device that wasn't using SSL/TLS inspection to begin with?
---

Sophos XG guides for home users: https://shred086.wordpress.com/
Cancel
Vote Up 0 Vote Down

Cancel
0 rfcat_vk over 4 years ago in reply to shred

Hi Shred,

I asked about setting up a firewall rule without DPI during the EAP. MichaelDunn responded with a very detailed explanation of how it all works.

I will search the EAP forums and up date this post with link to the answer.

Ian

XG115W - v20.0.2 MR-2 - Home

XG on VM 8 - v21 GA

If a post solves your question please use the 'Verify Answer' button.
Cancel
Vote Up 0 Vote Down

Cancel
0 Keyur over 4 years ago in reply to rfcat_vk

Hi rfcat_vk

Are you looking for this - https://community.sophos.com/products/xg-firewall/f/recommended-reads/118753/sophos-xg-firewall-v18-troubleshooting-problems-with-the-dpi-engine

Regards,

Keyur
Community Support Engineer | Sophos Support
Sophos Support Videos | Knowledge Base | @SophosSupport | Sign up for SMS Alerts |
If a post solves your question use the 'This helped me' link
Cancel
Vote Up 0 Vote Down

Cancel
0 rfcat_vk over 4 years ago in reply to Keyur

Hi Keyur,

thank you, that is probably a better link than the one I was after.

Ian

XG115W - v20.0.2 MR-2 - Home

XG on VM 8 - v21 GA

If a post solves your question please use the 'Verify Answer' button.
Cancel
Vote Up 0 Vote Down

Cancel

Reply

0 rfcat_vk over 4 years ago in reply to Keyur

Hi Keyur,

thank you, that is probably a better link than the one I was after.

Ian

XG115W - v20.0.2 MR-2 - Home

XG on VM 8 - v21 GA

If a post solves your question please use the 'Verify Answer' button.
Cancel
Vote Up 0 Vote Down

Cancel

Children

No Data

Unable to setup an Awair Glow device

Required WiFi Specifications