Thread Info
  • State Suggested Answer
  • +4 person also asked this people also asked this
  • Locked Locked
  • Replies 62 replies
  • Answers 2 answers
  • Subscribers 13 subscribers
  • Views 70673 views
  • Users 0 members are here
Options
Suggested
This discussion has been locked.
You can no longer post new replies to this discussion. If you have a question you can start a new discussion

Upgrade to UTM 9.601-5 firmware doesn't start FW NAT rules on boot

Daniel Huhardeaux

Hi,

I got information from my UTM that a new firmware 9.601-5 was available. I installed it and after reboot I discover that all my NAT rules where not activated ! I had to go on each one and disable/enable them to get back the working setup :(

I did it with some of them and then reboot the UTM: again rules where not applied. Disable/enable them and evrything is OK.

For some rules I didn't apply the "automatic firewall rules" in GUI but had create myself the FW rules: those NAT rules where activated. But for NAT rules with forwarding ports to other physical hosts but *not the host himself and the VMs running on it where the UTM lies* doesn't matter which setup (manual or automatically), I have to activate "automatic FW rules" and disable/enable the rules to get them working.

No need to say that prior firmware versions didn't had this problem.

Does anyone face the same problem and confirm?

Daniel



This thread was automatically locked due to age.
Parents
  • 0

    HI Everyone

     

    So glad to see this issue confirmed here - I am NOT going mad after all.  We've had some really big problems with this ; causing us embarrasment and our client's outages

    I can confirm the same activity on a few dozen of my UTMS - I am not sure what UTM firmware version this started with but I've seen it for a month or two at least. After a UTM reboot I need to DISable / ENable the NAT rules to get inbound NAT traffic started again. Not always ALL NAT rules it seems, can be just one rule out of dozens - I am now so scared to update firmware or reboot it's silly,  as I need to try every NAT rule after a reboot and I have so many UTMs to do this on. 

     

    Last post on this thread was Jun 7th - any updates from anyone yet?

     

    Thanks

    Grant AU

  • 0 in reply to GrantAU

    Hi Grant - welcome to the UTM Community!

    You might want to use the trick I outlined in April when this phenomenon first appeared.  If the issue only occurs at reboot, use "@reboot" instead of "0 4 * * *" in the cron jobs.

    Cheers - Bob

     
    Sophos UTM Community Moderator
    Sophos Certified Architect - UTM
    Sophos Certified Engineer - XG
    Gold Solution Partner since 2005
    MediaSoft, Inc. USA
  • 0 in reply to Daniel Huhardeaux

    Daniel Huhardeaux said:
    this morning I got answer from Sophos France support: working on our logs they found the problem which should be resolved with version 9.7 expected current october.

     

    9.7 seems to be pre-release ; I cant find an English readme or bugfix 

    Has anyone with access to 9.7 got confirmation on whether this is fixed yet - I have dozens of UTMs ready for updates but I am unwilling to update them if I then need to login to each one manually and STOP/START NAT Rules!   

     

  • 0 in reply to GrantAU

    Thanks for the feedback.

    I guess I will have to do it manually for a while again...

    Regards,

    DeltaSM

  • 0 in reply to DeltaSM

    If you don't want to wait till a solution is published you can set yourself FW rules and disable the "automatic create fw rules" switch.

    Daniel

  • 0 in reply to Daniel Huhardeaux

    Daniel - thanks for that info - I wasn't aware you could do that - I may need to do that to some of the clients who seem to need to reboot their UTM often (usually to get 4G USB Dongles to "reconnect") - but doing this to all my client devices will take hours and is just not possible.   Sophos should fix this. 

    Grant

     

     

     

  • 0 in reply to Daniel Huhardeaux

    Salut Daniel,

    Are you saying that the issue is the automatic firewall rule?  Do you see a default drop in the Firewall log (the KB article is misleading for the reasons I mention in the ?  If you look at the automatic rule on the 'Firewall' 'Rules' tab, does everything seem to be correct?  At the command line, is the 'status' of the rule 1?

    Cheers - Bob

     
    Sophos UTM Community Moderator
    Sophos Certified Architect - UTM
    Sophos Certified Engineer - XG
    Gold Solution Partner since 2005
    MediaSoft, Inc. USA
  • 0 in reply to BAlfson

    Hello Bob,

    yes, on automatic FW rules and yes, everything is OK in the 'Rules' tab (remember, it was working before I opened this thread connected to the 9-601-5 upgrade).

    This WE I upgraded an software UTM to 9.7-5 and problem disappears. Only thing is that after startup, it takes few minutes before rules are applied. I will check on the others I have not yet upgraded to confirm this.

    Daniel

  • 0 in reply to Daniel Huhardeaux

    Daniel Huhardeaux said:
    This WE I upgraded an software UTM to 9.7-5 and problem disappears. Only thing is that after startup, it takes few minutes before rules are applied. I will check on the others I have not yet upgraded to confirm this.

    I understand what happends: problem is NOT solved and there is no delay. To get it work you only need to disable/re-enable one rule and automagically all others are applied ! Doesn't matter which one you treat.

    Daniel

  • 0 in reply to Daniel Huhardeaux

    Hello Daniel,

     

    I've just updated my Sophos routers with firmware 9.700-5 and the problem is not solved.

    My worries is about NAT and FW rules that do not impact users behaviour directly who usually come to me to point out a malfunction. I mean ports like Pyzor, Razor, Spamassassin, ... that may be inactive and do not block the use of services but, in this example, takes my mail server out of date.

    I have so many rules and routers that I should disable/enable each of them to be sure none remain enabled but inactive.

    Saïd

  • 0 in reply to SAID NIAZI

    SAID NIAZI said:

    I have so many rules and routers that I should disable/enable each of them to be sure none remain enabled but inactive.

     

    As I ponted in my previous message, no need to go over each rule: disabling/enabling just one of them and all is good.

     

    Daniel

Reply Children
No Data
Unfiltered HTML