This discussion has been locked.
You can no longer post new replies to this discussion. If you have a question you can start a new discussion

Nothing showing up under IP Addresses Used.

I'm using a Home License on my UTM9 installation,
and although it says my limit is 50 users, it never shows
anything under "IP Addresses Used", basically 0 out of 50.


I am not complaining that it's not enforcing the license
properly, although I know I'm not over 50 devices either.

It used to count IP's at one point.

I've see other posts about it, but no solutions ...



This thread was automatically locked due to age.
  • Hi  

    Would you tell me if you're able to see Web Reports and other reporting data properly? Also, what troubleshooting steps you've taken so far?

    What do you see when you log into SSH as root and enter cc get licensing active_ips It should display you a list of all active IPs.

    Regards

    Jaydeep

  • To be honest I didn't troubleshoot it much, but yes all the reporting seemed to work ...

    I've tried backing up my config and restoring after a reset but it was the same.

     

     

    In the end I've setup the unit from scratch with all the settings yesterday, and today I see it populated :)

  • Hi  

    Thanks for the update. Let us know if you face the issue again. It might be an issue with gathering information from IPtables to check the active IP counts.

    Regards

    Jaydeep

  • Sounds good, I'll keep an eye on it and see if it starts going funky again :)

  • Well I believe this issue is somewhat related to the previous one I've seen ...

    This time Management Overview is not showing new logins or changes,
    however under Active IP I see a list, I'm suspecting it won't update though.

    This is on a brand new reset and all settings were configured again from webmin,
    so I know it's not an error in my backup - possibly one of the setting to blame.

    Other logs work just fine, network protection, usage, hardware, etc.

    See the log file frozen in time after September 17th ...

  • This time 'cc get licensing active_ips' does display a list of active IP's ...

  • I was correct, after a reboot and close to 2 day uptime the Active IP List is now still empty.

    This is after a full reset and manual setup of all the settings - same issue as before.

     

    cc get licensing active_ips shows []  -- that is empty.

     

    I've tried '/etc/init.d/postgresql92 rebuild' as well as 'psql -Ureporting -c"reindex database reporting;" reporting'  ...

     

    I think one of my settings is causing the licensing to show an empty list, as well as prevents showing new webadmin sessions ...

  • See my additional comments,- the issue is back even though I didn't do a restore and re-setup the box manually again.

  • Hi  

    Thanks for the posts and additional details. Since you've checked the database already, I assume there are no issues with the Log Disk partition filling up.

    Would you please check kernel, selfmon, fallback and system logs to see anything unusual coming up?

    Regards

    Jaydeep

  • As far as free space, I think everything looks fine:

    Log partition size:   25205 MB
     
    Free space:   23686 MB
     
    Current fillup rate:   0 MB/day
     
    Free space will be exhausted in   49710 days at current fillup rate.

     

    No error messages or weird entries in Kernel, Selfmon, Fallback, and System messages that I can see.

     

    Under user authentication I've noticed the following when logging in:

    2019:09:24-15:30:30 xxx aua[3512]: id="3006" severity="info" sys="System" sub="auth" name="Running _cleanup_up_children with max_run_time: 20"
    2019:09:24-15:30:30 xxx aua[3512]: id="3006" severity="info" sys="System" sub="auth" name="Child 17721 is running too long. Terminating child"
    2019:09:24-15:30:30 xxx aua[18644]: id="3004" severity="info" sys="System" sub="auth" name="Authentication successful" srcip="192.168.x.x" host="" user="admin" caller="webadmin" engine="local"

    Still nothing new in active ip addresses or last webadmin sessions.

     

    I should also add that under Application Control I see these types of messages, but I've always been getting them so I think they're safe to ignore:

     

    2019:09:24-15:40:08 xxx afcd[13286]: vy_plugin: E: failed to parse DNS RR in answer section of length 13 at offset 4 [...], unsupported resource records class (Resource temporarily unavailable)
    2019:09:24-15:40:31 xxx afcd[13286]: vy_plugin: E: failed to parse DNS qname: Resource temporarily unavailable in proto 17 packet of size 116 from 192.168.x.x:5353 to 224.0.0.251:5353 [...]

    I have a suspicion it's one of my settings that's causing this, but none of the settings I've changed should've been able to do this in the first place.

    Only that can explain why setting up the box twice, and re-doing all the settings manually would result in the same exact situation in the end.