This discussion has been locked.
You can no longer post new replies to this discussion. If you have a question you can start a new discussion

Das selbe Subnet auf zwei Netzwerkkarten

Hallo Forum,

ich würde gerne folgendes Szenario mit einer UTM realisieren:

Ich habe eine UTM ( VM unter VMWare ) mit zwei Netzwerkkarten.
Auf "eth0" ist das "Produktive LAN" und auf "eth1" das "Labor LAN".

Das Produktiven LAN sieht z.B. wie folgt aus:
Netz: 192.168.178.0/24
Gateway: 192.168.178.1
UTM eth0: 192.168.178.222
Server1: 192.168.178.10
Server2: 192.168.178.11
Server3: 192.168.178.12

Das Labor LAN sieht z.B. wie folgt aus:
Netz: 192.168.178.0/24
UTM eth1: 192.168.178.1
Server1: 192.168.178.10 ( Ein Klon des Server1 aus dem Produktiven LAN )

Auf dem Router ( Gateway ) ist eine Netzroute eingetragen, die das Netz 192.168.199.0 auf die UTM "eth0" ( 192.178.178.222 ) routet.

Grund der ganzen Aktion ist, einen Klon aus dem Produktiven LAN ohne Veränderungen ( IP, name etc ) im Labor LAN zu erreichen.
In diesem Fall will ich den Server1, der in beiden Netzen mit der selben IP vorhandne ist, über das Produktive LAN mit der IP 192.168.199.10 im
Labor LAN erreichen ( RPD, Telnet etc. ).

Leider gelingt es mir nicht dieses mit einer UTM nachzustellen.

Das es geht, weiß ich durch die Backup Software Veeam.  Hier gibt es ein sogenanntes "Virtual LAB" was genau dieses macht.
Es ist eine kleine Linux VM mit diversen "iptables" Einstellungen. Diese können natürlich per "Hand" angepasst werden, aber halt sehr umständlich.

Deshalb suche ich nach einen Weg über die UTM. Halt schön mit GUI.

Kann mir jemand helfen ?

 

 

 

 

 

 

 

 

 

 

 

 

 

 



This thread was automatically locked due to age.
Parents
  • Hallo Wolfgang,

    Erstmal herzlich willkommen hier in der Community !

    (Sorry, my German-speaking brain isn't creating thoughts at the moment.  )

    It's not practical to use your solution with the UTM.  WebAdmin is a GUI that manipulates databases of objects and settings.  A single change there can cause the Configuration Daemon to rewrite hundreds of lines of the code used to run the UTM.  You would never know when one of your manual changes at the command line would be overwritten by the Config Daemon.

    MfG - Bob (Bitte auf Deutsch weiterhin.)

     
    Sophos UTM Community Moderator
    Sophos Certified Architect - UTM
    Sophos Certified Engineer - XG
    Gold Solution Partner since 2005
    MediaSoft, Inc. USA
Reply
  • Hallo Wolfgang,

    Erstmal herzlich willkommen hier in der Community !

    (Sorry, my German-speaking brain isn't creating thoughts at the moment.  )

    It's not practical to use your solution with the UTM.  WebAdmin is a GUI that manipulates databases of objects and settings.  A single change there can cause the Configuration Daemon to rewrite hundreds of lines of the code used to run the UTM.  You would never know when one of your manual changes at the command line would be overwritten by the Config Daemon.

    MfG - Bob (Bitte auf Deutsch weiterhin.)

     
    Sophos UTM Community Moderator
    Sophos Certified Architect - UTM
    Sophos Certified Engineer - XG
    Gold Solution Partner since 2005
    MediaSoft, Inc. USA
Children
No Data